My Orders
AA Samsung Range - Overview
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$17.95
In Stock
Micro Door Switch
Part #3405-001034
This door switch, also known as a safety switch, is a genuine OEM replacement part for microwaves. It is a safety mechanism that sends signals to the microwaves control system, telling it when the door is open/closed. This ensures that the microwave only operates when the door is securely shut and switches off as soon as the door is open....Read more Over time, this switch can become worn out or damaged. A faulty door switch can result in failure to switch the microwave on/off, lack of heat, and running with the door open. To confirm that the door switch is faulty, use a multimeter to test for electrical failure. To remove the faulty switch, disconnect the wiring connectors and take note of where they are positioned. Place the new switch in position and reattach the wiring connectors to the appropriate terminals and close the microwave door to check that the switch engages appropriately.
Read less
$87.70
In Stock
Range Oven Temperature Sensor
Part #DG32-00002B
This is a range temperature sensor, used to detect the interior temperature of your oven when it is baking or cooking. If you notice your oven is baking unevenly or at inconsistent temperatures, will not start or has too little or too much heat, it is likely that the temperature sensor is bad, or defective. This temperature sensor feature...Read mores a 3.9-inch-long probe, 3.2-inch-long wire harness, and 1.7-inch-wide support bracket. Replacing this sensor is fairly simple but will require a screwdriver, wrench and drill with the appropriate Philips-head bit. Disconnect your range from the wall outlet and pull it out from the wall. Removing your range door is not necessary, but will make removing the sensor that much easier. You will now locate your temperature sensor, which will likely be near the heating element at the top/bottom of the oven. Remove any securing screws holding the heating element and/or sensor in place. At the rear of the range, disconnect and remove the rear panel to gain access to the electronics of the range. Disengage the sensor and its locking tabs, and may also require you to disconnect the terminals for the heating element if your temperature sensor is fastened to it. Remove the sensor and heating element (if necessary). If the sensor is connected to the heating element, use a wrench to unfasten it. Now you install the new temperature sensor and reassemble your oven, ensuring that wire terminals are connected correctly.
Read less
$27.95
In Stock
Leveling Leg
Part #DG61-00525A
The Black Leveling Leg from Samsung is a durable, genuine part designed for use with many Samsung kitchen appliances. This quality leg-leveling device offers an easy-to-use design to correct uneven surfaces, promising consistent performance to ensure your appliance is always level and stable. Carefully crafted by Samsung, it is compatible...Read more with select Samsung Range models. This component helps support your appliance, with adjustable height for seamless alignment. Upon purchase, rely on your owner's manual for detailed installation guidelines. Choose Samsung for reliable, long-lasting appliance parts.
Read less
$48.95
In Stock
Right Rear Burner Cap - Black
Part #DG62-00111A
This surface burner cap is specially designed to fit with Samsung ranges. It is a genuine OEM replacement part supplied directly by Samsung to ensure compatibility. The burner cap is a round, black cap that has a diameter of approximately 1.75 inches. It covers the burner head and helps to distribute the flame across the burner to ensure ...Read moreyour food is cooked evenly. The cap also protects the burner head from accidental food spillage and debris to keep your range running efficiently. The burner cap will need to be replaced if it is cracked or can no longer remain securely attached to the burner head. Each cap is sold individually.
Read less
$7.65
In Stock
Rubber Cushion
Part #DG73-00003A
This rubber cushion is supplied by the original manufacturer and has a shaft approximately 1 inch long. The cushion acts as a layer of protection between the oven door and oven frame/cavity. It prevents heat from escaping and protects the oven door and frame from abrasion and damage. If the rubber cushion becomes brittle or loses its elas...Read moreticity, you will likely notice heat escaping from the appliance, uneven cooking, as well as increased noise, and instability when opening or closing the door. Depending on your appliance model you may need to lift the top oven panel to access the cushion. Pull the faulty rubber cushion out from the oven frame and thoroughly clean the area where the new one will be placed to ensure a good seal. Press the new cushion into position and reassemble your oven to complete the repair.
Read less
$53.51
In Stock
Left Rear Burner Cap - Black
Part #DG62-00070A
Enjoy the precision and durability of Samsung with this high-quality Left Rear Burner Cap. Known as the "surface burner cap", this essential component is designed to cover the surface burner of your Samsung range. It serves as a protection against drips and splatters during your cooking sessions, enhancing longevity of your appliance whil...Read moree maintaining a clean, sleek look. This burner cap also assists in evening out the flame from the burner for consistent heating. Easily installable, this genuine Samsung part plays an intrinsic role in keeping your range functioning smoothly. Incorporate it today to ensure your Samsung range stays in pristine condition for your culinary adventures.
Read less
$108.95
In Stock
Wire Rack
Part #DG75-01001D
This stainless steel wire rack is a sturdy platform for baking or roasting food, making sure heat circulates evenly. It measures approximately 7/16 inches by 24 3/4 inches and is usually found inside the oven. You can adjust its height using the multiple slots in the oven cavity to suit your cooking needs. Please keep in mind that this genuine OEM replacement part is sold individually.
$51.95
In Stock
Burner Head
Part #DG62-00076B
The Samsung Burner Head (Aux) is a top-notch enhancement for your Samsung range. Specifically designed to endure high temperatures, this quality part, crafted from sturdy metal, ensures durability and maximum performance. It tightly holds the orifice and properly directs gas to the burner head for consistent and precise heat dispersion. T...Read moreo maintain safety, ensure the gas is shut off and the burner is cool prior to installation. Wearing gloves can provide additional protection for your hands. This impressive Burner Head (Aux) from Samsung not only ensures optimal functioning of your range but also enhances your cooking experience to a new level.
Read less
$82.95
In Stock
Range Surface Burner Cap
Part #DG62-00067A
The burner cap protects the burner head from spills and helps spread out the burner flame for even heating.
$70.69
In Stock
Burner Head
Part #DG62-00074C
Introducing the robust Samsung Right Burner Head, a full-length surface burner designed especially for Samsung ranges. Manufactured from hard-wearing metal, this genuine OEM item ensures exceptional durability and longevity, enhancing your cooking experience. Perfect for your right-hand burner needs, this Samsung-created marvel provides a...Read moren even flame distribution across the cooking surface for perfect heat balance. Before replacing, make sure to turn off the gas supply and disconnect the range from electricity. Also, remember to wear gloves to keep your hands safe. Trust the unsurpassed efficiency of Samsung to elevate your cooking to new levels.
Read less
$24.82
In Stock
Hexagon Nut Cap
Part #6021-001211
This hexagon nut cap, also known as a nut cover cap, is a nylon-insulated cylindrical cap with left-hand threads and a 4mm thread size, for counterclockwise tightening. It is sourced from the original equipment manufacturer for use in ranges and microwave oven combos. The cap provides added security to prevent the hexagon nut that it rest...Read mores on from coming loose during operation and causing component instability. Over time it is normal for the hex nut cap to wear down, become damaged, or for its threads to become stripped. To replace a faulty nut cap, use a socket or wrench to unthread it from the hex nut. Place the new cap in its position and secure it in place to complete the repair. It is recommended to replace the fastener at the same time for extended durability.
Read less
$54.42
In Stock
Burner Head
Part #DG62-00075B
Exact Part matches for your search term
No Longer Available
Common Symptoms of the AA
How this model fails, and the parts that fix it.
No heat
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Doesn’t shut off
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Won’t turn on
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Watch our pros, then fix it yourself.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More