Quick Question!

Have you ever purchased from PartSelect.com before?

Models > A101

A101 Maytag Washer - Overview

Get Parts and Repair Help for A101

If you know the washer repair part you need, you can browse the list of all parts on the A101, or you can search by name or part description. You can also find your part by where it is located on the A101 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for A101 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Exact Part matches for your search term

[Viewing 1 of 1]
$18.04

ACCY, LUNETA (1 PC)

This part number matches the current model number "A101".

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$24.68

Belt Kit

This kit includes both the drive belt and the pump belt which are both V-shaped. If your washer does not toss, spin, or drain water properly, this might be because one of these bel...

$52.96

Mounting Stem/Tub Seal Kit

This kit comes with a hub assembly, agitator seal, and spanner nut. If your washer leaks once it is full (with or without clothes in it) or leaks during agitation, then you should replace the seal. This part will also fix symptoms such as loud noises or the washer not agitating. The seal may become damaged or deteriorate over time and will need to be replaced. The mounting stem goes between the two tubs and seals the water into the tubs. When the water leaks, it goes into the bearing, which will cause it to also go bad, which is why you will likely change these at the same time.

$6.08

Rubber Foot Pad

The leveling leg pad or foot pad fits over the leveling leg on your washing machine. The foot pad is designed to protect your floor and keep the washing machine level and in place....

$45.89

Tub Bearing Kit

This kit is used on 2-belt washers. It is recommended to change the seal kit at the same time. The tub bearing kit fixes issues with leaking, loud noise, excessive shaking/moving or if your pump is not spinning. The tub bearing kit is fastened in the middle of the outer tub of your washer. The tub bearing ensures the inner tub is spinning effortlessly. If the rub bearing is faulty it might lock up and cause the washer to stop spinning. This is an OEM part that is obtained straight from the manufacturer.

$2.96

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air...

$7.69

Adjustable Levelling Leg

If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Your washer should be kept as close to the floor as possible. Your model might have rear legs that level themselves, or it might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This genuine OEM replacement part is sold individually, so be sure to order the amount you need.

$13.78

High Temperature Adhesive - 2oz.

$86.67

Drain Pump

This washing machine drain pump is intended for use with automatic washers that have been manufactured since 1958. The pump itself is made of plastic, though it does come with a metallic belt pulley.

$5.51

Hose Clamp

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washe...

$4.63

Tension Springs -Set of 2

This is a set of 2 tension springs.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leaking from around center shaft below fixed tub

  • Customer: douglas from bonita springs, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 468 of 478 people found this instruction helpful
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came a... read more

Drum would not drain and there was a banging noise when the drum spun

  • Customer: Charles from Whitman, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 350 of 186 people found this instruction helpful
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes ... read more

Clothes would come out of the spin cycle still wet

  • Customer: William from Cary, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 88 of 47 people found this instruction helpful
First found out where the belts were by tipping the machine backwards and saw that the belts were intact but extremely loose. Ordered two belts (Drive and Pump) . Re-tipped the machine and in less than three minutes, had installed the new belts. I re-hooked the hoses to the back and the machine operated as if new. read more