99944200610 Echo Trimmer - Overview

This is a repair kit for various models of trimmers to fix the line holding kit within the trimmer head. The parts within this kit allow the line, or string, within a trimmer to slowly feed out while the trimmer is in use, to provide the user with further line to cut weeds and other vegetation. Over time, the parts within this kit, such a...Read mores the pawls and springs, can wear out and will no longer hold the trimmer line and must be replaced. This kit includes 3 springs, 6 screws, 3 pawls and 3 hinge pins. Due to the high-use nature of these parts, replacing them more frequently may be required. • If you notice that the line is not being held within the trimmer head or gets stuck, it needs to be replaced immediately. Replacing these parts requires an Allen key, a wrench, a pair of pliers, and a flathead screwdriver.

This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends). This nut can have v...Read morearious uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.

This is a genuine OEM sourced replacement part designed for use with Echo blowers/trimmers. This is a standard hardware which has multiple applications based on your unit. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. To remove or install this screw you would need a screwdriver.

This is an original manufacturer approved replacement item commonly used on trimmers, brushcutters and edgers. The purpose of this nut is to secure cutter head assembly to the spindle/shaft of a trimmer. It is a metal nut which is sold individually. Please only use properly sized wrench when securing or removing this nut.

This is a genuine item that is supplied by the original equipment manufacturer for use with Echo attachments. The protective cap attaches to the pipe. A set of pliers might be necessary during the installation of this part. It is made out of rubber and will need to be replaced if it breaks. This item is priced individually.

This is a genuine Echo replacement part that has been sourced from the original manufacturer to be used with trimmers. The stopper is used to support the flexible liner to limit vibration inside the main pipe assembly. The stopper is sold as an individual replacement part, please note two stoppers may be needed.

This is an authentic replacement part manufactured for use with Echo backpack blowers, edgers, and trimmers. The screw has multiple applications that vary depending on the model of equipment. This screw is sold individually, please see model diagram for part location and usage.

The Spacer is a silver, metal part, which is rated as "Easy" to install. It can be attached between the bearing and oil seal in the gear box, to provide spacing between these parts. If broken, damaged or worn it should be replaced. Refer to your make, model and diagram to ensure this is the correct part for you.

This is a genuine manufacturer sourced replacement washer that is designed for use with Shindaiwa and Echo handheld lawn and garden equipment. It helps to distribute the pressure evenly between two connected parts, for proper application please make sure to check appropriate diagrams of your unit. This part is made from durable metal and it is sold individually.

This single-row, deep-groove ball bearing is sized at 12x32x10mm and is made of durable metal. It is used to reduce friction and vibrations when it is in between two parts that are rotating or moving against each other. This bearing can handle forces that are applied to it up-and-down and sideways, also known as radial and axial loads. It...Read more is easy to install and can handle high rotational speeds without causing too much vibration or making much noise. Over time, this ball bearing wears out from heat and pressure and starts to fail. If the engine of your machine has been run without oil in the gas tank, this ball bearing can seize. In these situations, you will need to replace the ball bearings. Otherwise, you will notice that your machine overheats, works harder because of the increased friction it is handling, and produces excessive vibration and noise. To extract a ball bearing from your machine, you will need to insert a flat-head screwdriver through the bearing opening and against the seal. Then, tap the seal out with a mallet. Afterwards, slot a socket through the diameter of the bearing, and tap the entire bearing out of its place by again using a mallet. This authentic OEM part is sold individually, so be sure to refer to your user manual to verify how many bearings your machine needs and where they are in it.