99944200600 Echo Brush Cutter - Overview

The m10 Left Hand Thread Nut is a 10mm, gold metal part, sold individually. This nut is a "reverse thread". It requires a wrench or socket set to install, and installation is rated as "Easy". Use this part to secure the blade to the unit, by attaching it to the shaft, securing the cutting blade. If broken or damaged, it should be replaced...Read more. Refer to your make, model and diagrams to check if this is the right part for you.

The Cotter Pin (or Split Pin) is a 2x22mm silver metal part, sold individually. It is rated as "Easy" to install, and installation will require a set of pliers. It can be attached in various locations on a variety of equipment and is used to secure and lock parts in place. If broken, damaged, or worn down the part it is securing may becom...Read moree loose, and the part should be replaced. If this part is removed for repairs, replace it with a new one. Refer to your make, model, and diagrams to make sure this is the correct part.

This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends). This nut can have v...Read morearious uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.

This is a genuine item that is supplied by the original equipment manufacturer for use with Echo attachments. The protective cap attaches to the pipe. A set of pliers might be necessary during the installation of this part. It is made out of rubber and will need to be replaced if it breaks. This item is priced individually.

This is a genuine Echo replacement part that has been sourced from the original manufacturer to be used with trimmers. The stopper is used to support the flexible liner to limit vibration inside the main pipe assembly. The stopper is sold as an individual replacement part, please note two stoppers may be needed.

The Blade Fixture is a silver, metal, individualy sold blade, which attaches at the bottom of the cutting head assembly, being held on by the nut and cotter pin. It is used to secure the blade fixing plate of the trimming tool. Installation is rated as "Easy" and requires a wrench and pliers to complete. If broken or damaged due to genera...Read morel wear, the cutting blade will not be secured, may be loose, or may not be able to stay on, which means you need to replace it. Refer to your make, model, and diagrams to ensure this is the correct part.

This is an authentic replacement part manufactured for use with Echo backpack blowers, edgers, and trimmers. The screw has multiple applications that vary depending on the model of equipment. This screw is sold individually, please see model diagram for part location and usage.

The shield kit is a kit containing the blade shield, the shield bracket, and all the necessary nuts, washers, and screws. Parts consist mainly of black metal. Installation is rated as "Easy" and will require a screw driver, pliers, socket set and nut driver. This kit attaches on the end of the trimmer around the cutting blade or string, a...Read morend prevents debris from flying out in all directions, and protects you from injury. If you notice physical damage due to general wear from use, replace the part. Refer to your make, model and diagrams to ensure this is the correct kit for you.

The Spacer is a silver, metal part, which is rated as "Easy" to install. It can be attached between the bearing and oil seal in the gear box, to provide spacing between these parts. If broken, damaged or worn it should be replaced. Refer to your make, model and diagram to ensure this is the correct part for you.

This is a genuine manufacturer sourced replacement washer that is designed for use with Shindaiwa and Echo handheld lawn and garden equipment. It helps to distribute the pressure evenly between two connected parts, for proper application please make sure to check appropriate diagrams of your unit. This part is made from durable metal and it is sold individually.

This single-row, deep-groove ball bearing is sized at 12x32x10mm and is made of durable metal. It is used to reduce friction and vibrations when it is in between two parts that are rotating or moving against each other. This bearing can handle forces that are applied to it up-and-down and sideways, also known as radial and axial loads. It...Read more is easy to install and can handle high rotational speeds without causing too much vibration or making much noise. Over time, this ball bearing wears out from heat and pressure and starts to fail. If the engine of your machine has been run without oil in the gas tank, this ball bearing can seize. In these situations, you will need to replace the ball bearings. Otherwise, you will notice that your machine overheats, works harder because of the increased friction it is handling, and produces excessive vibration and noise. To extract a ball bearing from your machine, you will need to insert a flat-head screwdriver through the bearing opening and against the seal. Then, tap the seal out with a mallet. Afterwards, slot a socket through the diameter of the bearing, and tap the entire bearing out of its place by again using a mallet. This authentic OEM part is sold individually, so be sure to refer to your user manual to verify how many bearings your machine needs and where they are in it.

The Upper Adapter Plate is a silver, metal part used to support the blade. It is the upper adapter on top of the blade that helps secure it in place. Installation is rated as "Easy" and requires pliers, and a wrench set. If broken or damaged, there may be a problem with it securing the blade, and it should be replaced. Refer to your make, model and diagrams to ensure this is the right part.