99944200532 Echo Pole Saw - Overview

This is a genuine OEM replacement part, it is sold individually. It is used in various places on the models shown below.. It is mainly use to secure parts such as Guide Bar Covers, Sprocket Guards etc.

This is an Authentic Part sourced from Original Manufacturer. This part is made out of Metal and it is Sold Individually. If the chainsaw bar doesn't adjust when you turn the tension screw usually the tension gear/pin or the adjustment bolt is worn or damaged.

This drive sprocket is made of high-quality metal and is designed for use with various makes and models of pruner, pole saw and trimmer. This sprocket is sold as an individual part and features 6 teeth/pins and a 3/8-inch pitch, which correlates to the distance between 3 consecutive rivets divided by two. If the chain for your equipment i...Read mores slipping or if the sprocket is worn down and worsening performance, the sprocket will need to be replaced immediately. Sprockets wear down easily because they are a high wear part, and thus will need to be replaced frequently, so it is recommended that you always have this part on hand since your equipment will not run as required without it.

This clutch washer, also known as a circular washer, is authentic manufacturer replacement part which is positioned on the crankshaft between the clutch drum and the engine. It is a circular metal ring with an outer diameter of 1 inch. The clutch engages with the clutch drum and sprocket to allow the chain to rotate when the engine accele...Read morerates. Over time, the clutch washer can wear out or become damaged due to normal aging, inadequate lubrication, or exposure to excessive heat. If the clutch washer is faulty, the chain will not engage or rotate properly, resulting in a loss of cutting power and poor engine performance. To access the clutch washer first remove the chain cover and bar, and then loosen and remove the clutch assembly. Carefully remove the old clutch washer and position the new one in its place. Ensure that it is properly aligned before reassembling the clutch assembly, chain, and bar.

This is a genuine item that is supplied by the original equipment manufacturer for use with Echo attachments. The protective cap attaches to the pipe. A set of pliers might be necessary during the installation of this part. It is made out of rubber and will need to be replaced if it breaks. This item is priced individually.

This component is supplied by the original equipment manufacturer for Shindaiwa and Echo lawn and garden equipment. It is an important part of the chain tensioning mechanism. Unfortunately, over time collars tend to wear out and they may begin to fail eventually requiring a replacement. Check the diagrams for your model to ensure the prop...Read moreer repair procedure. You may need a screwdriver and a wrench set to replace this component.

This is an authentic Echo replacement part manufactured for use with Echo power pruners. The special hex socket screw is commonly used to secure the oil tank to the gearcase. This screw is available as an individual replacement part, please see model diagram for associative parts.

This is an original replacement part manufactured for use with Echo chainsaws. The oil strainer filters oil as its is picked up to lubricate the chain. Proper lubrication between the chain and bar cuts down on friction extending the life of the saw. It is recommended to check the oil strainer before each use, and to clean or replace as necessary to prevent blockage. The oil strainer is sold individually.

This replacement cap assembly is supplied directly from the original equipment manufacturer for use with Echo handheld lawn and garden equipment. It is used to keep the fuel in the tank, note this assembly includes a retainer that remains in the tank to prevent the cap from falling out. It is made of high-quality plastic material and it is sold individually.

This is an original Echo replacement part manufactured for use with outdoor power equipment. The vent assembly is used like a one-way valve to allow air into a fuel or oil tank to prevent a vacuum within the tank. This vent assembly is sold individually.

This authentic OEM replacement bolt is made for chainsaws and pole pruners. It is an important part of chain tensioning mechanism which allows users to adjust tension of the bar. If the bar doesn't adjust when you turn the tension screw usually the bolt or pin is worn or damaged. This bolt has a hex socket head requiring a hex key/allen wrench for installation. Includes one (1) bolt per order.