9910X Makita Sander - Overview

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

This #191938-1 (CB-408) Makita carbon brush set contains two individual carbon brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes are often the cause...Read more of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This authentic replacement part which is specially designed for use with Makita power tools. Ball bearings are used to reduce friction between rotating parts, over time components may begin to wear out and fail eventually requiring a replacement. Please note this high-quality ball bearing is made of durable metal and it is sold individually.

This cord guard is a genuine Makita replacement part, and it is a direct replacement for a damaged or missing cord guard. Power tool cords undergo a lot of stress, and these cord guards help to alleviate some of that stress at the weakest point--right where the cord enters the tool. Over time cord guards will deteriorate and eventually re...Read morequire replacement. Keeping a strong cord guard on your tool will help will cord life. This cord guard is compatible with the tools listed below, but it is not guaranteed to fit any other power tools.

This replacement tapping screw is an authentic item that is supplied by the original manufacturer for use with Makita power tools. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this part. This high-quality phillips pan-head screw is made of durable metal and it is sold individually.

This replacement ball bearing is designed for power tools to reduce friction and support smooth, reliable rotation of internal components. Built for durability and precise fit, it helps restore proper motor and shaft operation when an original bearing becomes worn or noisy. It’s a practical maintenance replacement for maintaining consistent performance and extending the service life of power equipment.

This authentic OEM part is compatible with various handheld power tools made by Makita including jig saws, routers, and sanders. A bearing\\\'s main purpose is to decrease friction between moving parts. They also stabilize parts to keep proper direction and angle. Bearings are high wear items that may need regular replacement. Sold individually. Included in part number 517266-0 Armature Assembly 115V

This Ball Bearing is sealed on both sides. This is a genuine Makita replacement part that is sold individually. • Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear...Read more on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

• Belt Width - 1/4" • Belt Length - 12" This drive belt is a genuine Makita replacement part. This is a reinforced toothed belt. It is used on the tools listed below. Over time, all belts require replacement due to wear. This belt will be an exact replacement for your old belt.