9835XVB Magic Chef Wall Oven - Instructions

Removed two screws holding oven sensor in place. Haad to remove part of the back to access wires. Found existing wires had burnt up, and had to reterminate same. Installed new sensor, making sure the leads did not come in contact with the rear of oven compartment. (This may have been what caused failure to begin with)

The sensor inserts into a slot in the back side of the range. By removing screws on the heat shield on the backside of the range, the sensor wires will be exposed can be unplugged. Then remove the screws that attach the sensor to the back inside panel in the oven. Next, pull the old sensor out. The wire leads will get caught on the insulation blanket, no big deal. Reverse the process to install the new sensor. The new sensor comes with two connector sets for the wiring. I did the whole job for less than the cost of a service call.

The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in place and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.

We took the back off the stove and unscrewed the two screws from the inside holding the sensor on and pulled it through and plugged it in and then replaced the screws. Very easy. We are still having trouble as the display does not read the same as the tempature is in the oven.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

Upon receiving the replacement part, I noted that the socket was held in place by simple expanding tabs. TURN OFF POWER TO THE OVEN. Using a right angle pick or similar tool, bend the tabs inward on the existing socket and remove. Disconnect the white, black and green wires. Note which tab is the green tab. Attach the wires to the new socket. Push the new socket into place, aligning the key bump on the socket with he slot in the oven wall opening. Install bulb and diffuser.

The "PartsSelect" General discription of the parts funtion helped me to confirm my suspitions that there was some form of temperature registering problem. I whatched the short video they provided on how to change the part out, even though, in this case, it's pretty self explanitory.The part was in my hands a day erlier than promised and in reality, much earlier than I had anticipated from the beginng. It took me all total, 20 minutes to exchange the part out and have the oven in operation again.

Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call

1. Turned off oven electric power at circuit breaker.. 2. Removed 2 screws at coil at back of oven. 3. Pulled coil away from back of oven. 4.Pulled power wire clip up vertically from coil.One clip was too tight to pull up by hand. Used a pair of pliers. 5 Removed coil and put new coil in place with wireclips. and screws provided.

Watched the video and things went exactly as planned. Love this website will use them again when I need a repair.

removed 2 screws in probe and pulled it out.had to take back off as wire was tangled from factory and couldn't do quick repair

Turned off the circuit breaker. Removed the oven door from hinges. unscrewed the old element connection plate. Pulled off two wire leads. Reversed forward steps to completion.

put the old one out,put new part in that easy,works like new

Very simple. Removed two screws-pulled element out about 3-4 inches-pulled off the contacts-reversed procedure using the provided screws, turned the breaker switch on and everything worked fine. Excellent service from parts select and quick shipping.

I removed the old sensor via the two screws holding it in, unplugged it and replaced it with a new one.