96142004301 Poulan Lawn Mower - Overview

This blade is sourced directly from the manufacturer for use in Craftsman and Husqvarna lawn mowers. The blade is the part of the mower that is responsible for cutting and mulching the grass. It is 22" long, made of black metal, is not part of a kit or assembly, and is sold individually. If you hit a hard object, you may bend the blade,...Read more causing a vibration. You may also have problems with the grass being cut as the blade dulls over time. If the blade is bent, damaged, or worn, it needs to be replaced. You will need a socket set to complete this repair. Customers rate this repair as Easy.

The Dust Shield is a 6-3/4 inch, black plastic part, used to prevent dust or debris fouling the wheel or axle. It attaches inside of the wheel around the axle. Installation is rated as "Easy" and will require a wrench. If broken, damaged, or worn due to fatigue, you will see visable damage and you may have debris getting caught in the axl...Read moree. If broken, replace it. Refer to your make, model and diagram to make sure you're choosing the right part. This part comes individually sold.

It is a genuine OEM supplied item which is made for walk-behind lawn mowers. This is a high-quality replacement for a missing or a damaged pinion gear that helps to drive the mower's wheel. Unfortunately, over time due to friction, the teeth on the gear may wear out. If this happens it will no longer engage the wheel and the mower will no...Read moret move. To ensure the exact location and the correct installation of the new part, refer to the diagrams of your specific model. Note, one durable metal pinion is included. You will need a wrench set and pliers to remove the old pinion and secure the new one.

Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carriage bolt and is an important component to the axle assembly. This locknut has a 3/8-inch inner-diameter and is 16 threads-per-inch. To repl...Read moreace this locknut, you will need a wrench, and if there are multiple locknuts on your equipment, they may all need to be replaced.

This replacement part is supplied directly from original equipment manufacturer for use with walk behind/push mowers. The drive control cable is the cable that stops the blade when the control handle is released. If the cable is broken it will cause the brake to not release even when the lever is pressed. This cable assembly consists of a...Read more metal wire cable with z-type bent ends, rubberized cover/body and a plastic clip. Replacing this cable is a simple task that may require pliers. • First you want to see where the old cable is attached • Just remove one cable end there and install the new one • Now you can run the new cable up to the control handle • Then just as the old cable, put the z-shaped end through the hole in the control handle • Once both ends are attached, push the upper mount assembly of the old cable out of the hole in the upper handle • Tie the cable in place just as the old one was (make sure to leave enough clearance and free play to avoid over-bending and breaking the new cable)

The E-Ring 7/16 is a 7/16-inch silver, metal part which can be attached to various locations on a variety of equipment to snap into grooves and secure parts into place. This part will require pliers to install. If broken, damaged or worn, there may be a problem with the part it is securing and the part should be replaced. Refer to your make, model and diagrams to check if this is the right part.

Keep your equipment powered and ready with this authentic OEM 12V battery charger, specifically designed for use with Husqvarna and Poulan lawn mowers. Sourced directly from the original manufacturer, this charger ensures reliable performance and compatibility—unlike aftermarket alternatives. Its primary function is to recharge the bat...Read moretery that powers your mower, helping maintain consistent starting power and overall functionality. Please note that using this charger with a weak or defective battery can cause damage to the charger itself. If you're unsure whether the issue lies with the battery or the charger, it's recommended to have the battery tested at a certified service center before replacing any components. Each order includes one (1) 12V charger. This is a must-have replacement part for maintaining your mower’s electrical system and ensuring dependable operation throughout the season.

This washer is not part of a kit or assembly. It is sold individually. With an O.D. of 1 inch, this OEM replacement part is made of dark grey metal and is used to provide a tight seal between the mower blade and the blade bolt/screw. This part should be replaced if you notice any visible wear, warping, or damage. You will need a wrench or socket set to complete this repair. Customers rate this repair as Easy.

This is a genuine manufacturer-sourced replacement screw which is specially designed for use with Craftsman lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please refer to the appropriate diagrams for the correct location and use of this item. This part is made of h...Read moreigh-quality metal and it is sold individually, you will need a wrench to secure or remove it.

Lawn mower front wheel. 8" X 2"

This deflector shield torsion spring is an original part from Craftsman for lawn mowers, rotary mowers, and gas walk behind lawn mowers. This part connects to the hinge rod and allows the shield to hinge down and up. You will need pliers to replace this part. This deflector shield torsion spring is made of metal and sold individually.

This is a genuine Craftsman selector knob that is specifically made for use with a walk behind lawn mower. This selector knob attaches to the adjustment lever giving the user a comfortable grip when adjusting the mower deck to the desired cutting height. This part is made of a durable plastic and is sold individually.