96142002501 Poulan Lawn Mower - Overview

The Dust Shield is a 6-3/4 inch, black plastic part, used to prevent dust or debris fouling the wheel or axle. It attaches inside of the wheel around the axle. Installation is rated as "Easy" and will require a wrench. If broken, damaged, or worn due to fatigue, you will see visable damage and you may have debris getting caught in the axl...Read moree. If broken, replace it. Refer to your make, model and diagram to make sure you're choosing the right part. This part comes individually sold.

This Genuine OEM blade control cable assembly is designed for use with walk-behind and push lawn mowers. Sold individually, it includes a durable metal wire cable with Z-type bent ends, a rubberized protective cover, and a plastic mounting clip. This essential component connects the control handle to the engine brake system, stopping the ...Read moreblade when the handle is released to ensure safe operation. If the cable is broken, the brake may remain engaged even when the lever is pressed. Replacing the cable is a straightforward process that may require a pair of pliers. Begin by identifying where the old cable is attached to the motor assembly and remove it. Install the new cable in the same location, then route it up to the control handle. Insert the Z-shaped end into the hole in the control handle, just as with the original cable. Once both ends are connected, remove the upper mount of the old cable from the handle and secure the new one in its place. Finally, tie the cable in the same manner as the original, ensuring there is enough clearance and free play to prevent over-bending or premature wear. This replacement restores proper blade control and helps maintain safe mower operation.

This is a genuine OEM sourced replacement part used on lawn mowers. Mulching blades are designed to circulate the grass longer so it can be cut into smaller pieces. This makes your grass clippings better as mulch since the smaller clippings will decompose more quickly, releasing their nutrients into the soil. This part is made out of meta...Read morel and it is sold individually. To replace it you would need a wrench to remove the nut that secure the blade.

Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carriage bolt and is an important component to the axle assembly. This locknut has a 3/8-inch inner-diameter and is 16 threads-per-inch. To repl...Read moreace this locknut, you will need a wrench, and if there are multiple locknuts on your equipment, they may all need to be replaced.

The E-Ring 7/16 is a 7/16-inch silver, metal part which can be attached to various locations on a variety of equipment to snap into grooves and secure parts into place. This part will require pliers to install. If broken, damaged or worn, there may be a problem with the part it is securing and the part should be replaced. Refer to your make, model and diagrams to check if this is the right part.

This washer is not part of a kit or assembly. It is sold individually. With an O.D. of 1 inch, this OEM replacement part is made of dark grey metal and is used to provide a tight seal between the mower blade and the blade bolt/screw. This part should be replaced if you notice any visible wear, warping, or damage. You will need a wrench or socket set to complete this repair. Customers rate this repair as Easy.

This is a genuine manufacturer-sourced replacement screw which is specially designed for use with Craftsman lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please refer to the appropriate diagrams for the correct location and use of this item. This part is made of h...Read moreigh-quality metal and it is sold individually, you will need a wrench to secure or remove it.

This deflector shield torsion spring is an original part from Craftsman for lawn mowers, rotary mowers, and gas walk behind lawn mowers. This part connects to the hinge rod and allows the shield to hinge down and up. You will need pliers to replace this part. This deflector shield torsion spring is made of metal and sold individually.

This hinge rod is an OEM part direct from Craftsman for lawn mowers and gas walk behind lawn mowers. This part holds the chute to the hinge bracket, which allows the chute to hinge down and up. It is recommended to review your models diagram to verify the parts compatibility. This part is made of metal and sold individually.

This replacement part is supplied directly from the original equipment manufacturer. It is specially designed for walk-behind lawn mowers. The bracket is an important component which helps to provide support for the deflector. This is an identical replacement for a damaged or a missing part that was installed on a new unit. Keep in mind t...Read morehis high-quality hinge bracket assembly is made of durable metal and is sold individually. Make sure to refer to the diagrams of your model for the correct installation of the new part. Note, the hardware to secure it is sold separately.

This manufacturer certified 1/4 Hex Nut can be installed using a wrench or socket and is used to secure parts in place and spead the load. If the part being secured seems loose, check this nut and replace it if broken or missing. Refer to your make, model and diagrams to ensure this is the right part for you.

This is a genuine OEM replacement part used on a variety of Lawn and Garden Equipment. This part is made out of Metal and it is Sold Individually. This steel washer has several applications based on your unit. Please refer to diagrams for proper application.