96046000800-2007 Poulan Lawn Tractor - Overview

The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle. This part is black, made of metal, and around an inch in length. It is sold individually and may become damaged over time due to wear and fatigue.

This part is the replacement washer head screw for your lawn tractor. It is black in color and is approximately an inch and a half in length. This self-threading screw is most commonly used for securing the mandrel housing to the mower deck of your lawn tractor. The main reason you would need to replace this part is if the old screw is da...Read moremaged or missing. This part is sold individually and is a genuine OEM part sourced directly from the manufacturer.

This genuine black cap axle, also sometimes known as the dust cap, is around 2 inches in diamater and sold individually. Comprised of plastic, it is designed to keep debris out of the hub and axle of your lawn mower or garden tractor. Over time, your dust cap may become damaged or lost due to wear and tear. If this happens, dirt and debri...Read mores can freely enter the axle and hub, causing damage. This is an easy repair to make and does not require any tools. Just look for the cap axle on the rim of the wheel to make your repair.

This lawn tractor mandrel assembly supports and drives the mower blade, ensuring smooth and stable rotation during operation. Built as a durable, all-in-one unit with internal bearings and shaft, it helps maintain consistent cutting performance while protecting the mower deck from impact damage. Replacing a worn or damaged assembly can restore proper blade function and ensure reliable, even cutting results.

The manufacturer-approved Ratchet Pawl (Starter Pawl) comes in a set of two (2). This part attaches inside the recoil assembly, and is used to engage the flywheel. if broken due to wear/damage it will have a hard time engaging the fly wheel, making the engine harder to start, and should be replaced. Installation is rated as "Easy" by cust...Read moreomers, and will require a screwdriver, pliers and nutdriver. Refer to your make, model and diagram to ensure this is the correct part for you.This model is plastic and comes in white.

This OEM Seal-Oil (PTO Side), also called the Oil Seal, is a Black, Nitrile Rubber, 2/14 O.D., individually sold part which is installed using a Seal Puller. Customers rate the installation difficulty as Medium. This part provides a seal around the crank shaft and engine block. When installing onto the engine block around the crank shaf...Read moret, use something that makes contact around the entire seal, like a large socket or pipe, and tap into place evenly, ensuring that the housing is clean and dry. If the part is broken, likely due to fatigue, there will be leaking oil, and this part should be replaced using the model number on the original part to confirm it is the right fit for your model.

This spark plug is designed to provide reliable ignition and efficient fuel combustion in small engine applications. Built for consistent performance and durability, it helps maintain smooth operation, steady power output, and easier starting. Ideal for routine maintenance or replacement, it supports dependable engine performance in lawn and garden equipment, generators, and similar outdoor power machines.

This ignition switch is an OEM replacement part found near the steering wheel or dashboard in lawn tractors and riding mowers. The switch has four symbols on the top side which indicate its various functions including starting, stopping, running and reversing. The switch works by connecting/disconnecting the circuit between the battery an...Read mored the ignition system. The switch can fail either from physical damage or faulty electrical wiring. If the ignition switch is no longer working, you will not be able to operate your equipment. To access the faulty switch, first disconnect the battery, and wiring harness. Squeeze the tabs on the sides of the switch and pull it out from its mounting position. Plug the new switch in place and ensure that the tabs are engaged. Finish the repair by reconnecting the wiring harness and battery. If your current key is in good working condition, you can continue to use it. However, if it is not, it is recommended to replace the key at the same time. Each ignition switch is sold individually.

This OEM Gasket Rocker Cover, which can also be called the Valve Cover Gasket, is used to provide a seal between the valve cover and engine. This is a gray-colored part, measuring 5 1/2 x 4 Inch, and it is sold individually. It can be attached using a wrench or socket. Note: this part also requires a Torque Wrench. When installing, tighte...Read moren and torque in alternating patterns, following the manufacturer specficiations. You will know when it needs to be replaced when there is oil leaking around the valver cover gasket, which is a sign the part is broken, likely due to simple wear and tear or constant dryness. To make sure you are purchasing the right part, check your model number. Customers rated this repair as easy.

The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "Medium" difficulty and requires a screw driver, wrench set and seal puller. A broken seal will cause a leak, and the part must be replaced. R...Read moreefer to your make, model and diagram to ensure you're choosing the right part. This part comes in black and gray.

This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in length. Your machine may have a loud hissing or popping sound coming from the exhaust area if the gasket was faulty. You may also notice th...Read moree presence of black soot around the gasket or the exhaust. Your gasket needs to be replaced if it appears worn or deformed. Otherwise, your machine will experience exhaust leaks. To detach the gasket, remove the fasteners that secure it using a socket or wrench. You can detach the gasket from your machine afterwards. Please bear in mind that this replacement part is sold individually.

This item is an authentic OEM replacement part that is intended to be used with small engines from Briggs & Stratton. The breather tube is used to guide the direction of excess gasses and fluid that escape the engine from a higher level of internal pressure. The breather tube is a single item, please see the model diagram for related parts.