96042005900 Poulan Lawn Mower - Overview

This lawn tractor mandrel assembly supports and drives the mower blade, ensuring smooth and stable rotation during operation. Built as a durable, all-in-one unit with internal bearings and shaft, it helps maintain consistent cutting performance while protecting the mower deck from impact damage. Replacing a worn or damaged assembly can restore proper blade function and ensure reliable, even cutting results.

This ignition switch is an OEM replacement part found near the steering wheel or dashboard in lawn tractors and riding mowers. The switch has four symbols on the top side which indicate its various functions including starting, stopping, running and reversing. The switch works by connecting/disconnecting the circuit between the battery an...Read mored the ignition system. The switch can fail either from physical damage or faulty electrical wiring. If the ignition switch is no longer working, you will not be able to operate your equipment. To access the faulty switch, first disconnect the battery, and wiring harness. Squeeze the tabs on the sides of the switch and pull it out from its mounting position. Plug the new switch in place and ensure that the tabs are engaged. Finish the repair by reconnecting the wiring harness and battery. If your current key is in good working condition, you can continue to use it. However, if it is not, it is recommended to replace the key at the same time. Each ignition switch is sold individually.

This lightbulb is supplied by the original manufacturer and intended for use in lawn tractors and riding mowers with a 12-volt system. It is positioned on the front of the equipment as part of the equipment lighting system. The lightbulb illuminates the area allowing for improved visibility when working in low-light conditions. The lightb...Read moreulb can fail due to various reasons, such as burnout, electrical issues, or physical damage. Once the lightbulb stops functioning, visibility will be reduced which makes it difficult to safely operate the equipment. Before you begin the repair, disconnect your equipment from the power source to avoid electrical hazards. Remove the bulb housing cover, and carefully unscrew the old bulb. Thread the new bulb into the housing and ensure that it is securely seated. Finally, reattach the housing cover, reconnect the power supply, and test the new bulb. Note that this bulb is part of a dual usage system, therefore ensure that you order at least two as each bulb is sold individually.

It is a genuine manufacturer-approved part which is specially designed for Ryobi and Husqvarna riding lawn mowers and garden tractors. The purpose of the switch-interlock is to act as a safety feature which will shut the engine off when equipment is started or running in unsafe operating conditions. Unfortunately, over time parts will wea...Read morer out and it may begin to fail eventually requiring a replacement. Refer to the owner\'s manual and the appropriate diagrams for your model for the correct location and installation of this component. Note, this high-quality plastic body interlock switch is sold individually. You will need a screwdriver to perform this repair.

This headlight switch is designed for use with various models of ride-on mowers/tractors, features an on/off mode for turning the headlines on and off, and is a genuine OEM part. If your headlights do not turn on, it is recommended that you inspect the light bulbs before replacing this switch. It is recommended that if you have a multimet...Read moreer, you test this switch for continuity prior to ordering a new switch. To replace this switch, lift or gain access to the steering housing of the lawnmower. Locate the tabs securing the switch, which will be underneath where they appear on the user interface panel. Push the tabs on the side of the switch inwards to release the switch out from its panel, and then disconnect the wires from the switch, taking note of their positions. Connect the new switch terminals to the previous wires, push the new switch into its panel, and test the lights to make sure they work.

It is a genuine OEM sourced part is specially designed for riding lawn mowers and garden tractors. The solenoid acts like an electromagnetic switch, it engages and routes the battery electrical supply to the engine starter when the ignition switch is rotated to the start position. Unfortunately, over time it may wear out or get damaged ev...Read moreentually requiring a replacement. Keep in mind this high-quality solenoid is sold individually. You will need a screwdriver and a wrench set to perform this repair. Check the diagrams of your model for the exact location and the correct installation of the new part.

It is a genuine part which is supplied by the original manufacturer for use with Husqvarna and Poulan riding lawn mowers and garden tractors. This replacement switch is secured under the seat to act as a safety feature, the mower will only start if the user is properly seated and it will shut down the mower if the user falls out of the se...Read moreat. Over time switches may develop either electrical or mechanical issues eventually failing and requiring a replacement. Please note this high-quality component is made of durable plastic and it is sold individually.

This item includes two ignition keys that are used with riding lawn mowers and garden tractors. It is used to turn the starter ignition to easily start the engine. This key/chain is a genuine item that is sourced directly from original equipment manufacturer. Note these keys are not universal for all units, they are model specific so make sure to check your model and serial numbers.

This part is an OEM from Husqvarna, Poulan and Weed Eater for use with Lawn Tractors. The Interlock switch disables the ignition system if it detects the lawn tractor is started or running in unsafe operating conditions. The most common reasons for replacing the clutch interlock switch are when the mower won't start or starts when the bra...Read moreke is not depressed. This part is sold individually. The tool that you will need to replace the clutch interlock switch is a -+ inch socket.

This ignition chassis wiring harness is designed to connect and protect the electrical circuits that support your equipment’s ignition system, ensuring reliable power flow between the engine, controls, and battery. Wrapped in durable protective insulation, it helps shield internal wiring from heat, moisture, and debris for long-lasting pe...Read morerformance. Ideal for replacing damaged or worn harnesses, it helps restore proper electrical function and dependable operation in your equipment.

This is an OEM part sourced directly from the manufacturer. The bulb socket assembly is commonly found in riding mowers and lawn tractors from Husqvarna, Poulan, and Weed Eater. This part is made of high-quality plastic and metal, and is used to hold the light bulb and provide electricity in the headlamp assembly. This item is available as an individual replacement part.

The screw is made of metal. It is a genuine OEM sourced part which is specially designed for use with lawn mowers and lawn tractors made by Poulan, Husqvarna, and Weed Eater. This item is available as an individual replacement. During replacement, it may require a wrench to help install this part correctly. It will need to be replaced if it strips or breaks.