96012002803 Poulan Lawn Tractor - Overview

The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle. This part is black, made of metal, and around an inch in length. It is sold individually and may become damaged over time due to wear and fatigue.

This part is the replacement washer head screw for your lawn tractor. It is black in color and is approximately an inch and a half in length. This self-threading screw is most commonly used for securing the mandrel housing to the mower deck of your lawn tractor. The main reason you would need to replace this part is if the old screw is da...Read moremaged or missing. This part is sold individually and is a genuine OEM part sourced directly from the manufacturer.

This replacement blade is supplied directly from the original equipment manufacturer for use with Craftsman riding lawn mowers and garden tractors. It is secured under the deck to cut the grass, over time the blade may become dull or damaged causing irregular cutting patterns. Inspect your blades periodically and replace them as needed to...Read more maintain a clean cut lawn. It is a high-quality component which is made of durable steel and it is sold individually.

This ignition switch is an OEM replacement part found near the steering wheel or dashboard in lawn tractors and riding mowers. The switch has four symbols on the top side which indicate its various functions including starting, stopping, running and reversing. The switch works by connecting/disconnecting the circuit between the battery an...Read mored the ignition system. The switch can fail either from physical damage or faulty electrical wiring. If the ignition switch is no longer working, you will not be able to operate your equipment. To access the faulty switch, first disconnect the battery, and wiring harness. Squeeze the tabs on the sides of the switch and pull it out from its mounting position. Plug the new switch in place and ensure that the tabs are engaged. Finish the repair by reconnecting the wiring harness and battery. If your current key is in good working condition, you can continue to use it. However, if it is not, it is recommended to replace the key at the same time. Each ignition switch is sold individually.

This hairpin clip, also known as a cotter pin, is a genuine OEM sourced part used to secure rotating components together in various outdoor power equipment. It is made of steel and is approximately 1.5 inches long. The clip acts as a fastener to prevent the moving parts from loosening and falling off during usage. The clip is vulnerable t...Read moreo corrosion and general wear over time. However, it can also fail prematurely due to overloading and excessive stress. A damaged hairpin clip will result in misalignment of parts, accidental disassembly, increased friction and wear, and potential harm to the user. Remove the faulty pin and align the new one with the insertion points. Ensure that the pin is securely fitted in its appropriate slot and compress the ends to prevent it from dislodging.

This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in length. Your machine may have a loud hissing or popping sound coming from the exhaust area if the gasket was faulty. You may also notice th...Read moree presence of black soot around the gasket or the exhaust. Your gasket needs to be replaced if it appears worn or deformed. Otherwise, your machine will experience exhaust leaks. To detach the gasket, remove the fasteners that secure it using a socket or wrench. You can detach the gasket from your machine afterwards. Please bear in mind that this replacement part is sold individually.

This is a genuine replacement belt sourced directly from the original manufacturer, designed for use with riding lawn tractors and mowers. Made from durable rubber and sold individually, this belt is responsible for driving the mower blades, making it a critical component for cutting performance. To ensure optimal function and longevity, ...Read moreit’s important to clean the pulleys before installing the new belt and to inspect the belt regularly for signs of wear or stretching. Replacing the belt requires a wrench set and pliers. For safety, always disconnect the spark plug wire before beginning. Start by lowering the mower deck to its lowest position and setting the blade engagement lever to the "Off" position. Roll the old belt off the engine pulley from between the belt guide and pulley. Remove the mower deck by taking out the bow-tie pins securing the left and right lift arms, then disconnect the blade engagement cable. Next, remove the bolts from the mower deck belt pulley covers and take off the covers. Loosen, but do not remove, the nuts on the top of the idler pulleys. Install the new mower deck belt through the belt guides and around the pulleys, then tighten the idler pulley nuts. Finally, reassemble the deck to complete the repair and restore your mower’s cutting performance. Lawn mower deck belt. Width: 1/2 " Length: 95 1/2 ".

Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carriage bolt and is an important component to the axle assembly. This locknut has a 3/8-inch inner-diameter and is 16 threads-per-inch. To repl...Read moreace this locknut, you will need a wrench, and if there are multiple locknuts on your equipment, they may all need to be replaced.

This Genuine OEM latch assembly is designed for use with select Poulan lawn tractors and is sold individually. Constructed from a combination of durable metal and plastic, this component is engineered to secure the discharge chute to the mower’s chute adapter, ensuring a stable connection when using a mulch or bagger system. Proper instal...Read morelation of this latch helps maintain efficient grass collection and safe mower operation. The latch is fitted onto the bagger chute adapter and may require a wrench and screwdriver for removal and replacement. For best results, refer to your equipment’s specific manual for detailed repair instructions and compatibility. Replacing a worn or broken latch ensures a secure fit and reliable performance during mowing.

This genuine OEM compression seat spring provides support and cushioning for the seat of your lawn equipment. It also effectively absorbs shocks and vibrations from uneven terrain. Typically, you can find it connected to the seat frame on the fender of your machine. If one or both springs are broken, your seat may feel unstable or uneven,...Read more compromising your comfort. It is essential to replace any damaged springs to restore a smoother ride. To replace the spring, gather a socket or wrench. Ensure your machine is turned off and engage the parking brake. Consult your user guide to locate the spring, which may be accessible from the underside of the seat or by removing the seat cushion. Use the socket or wrench to remove the fasteners securing the spring. Lift the spring off your machine carefully. Remember, different springs are used in your machine, so refer to the parts diagram to order the correct part. Also, note that this replacement part is sold individually, so confirm how many springs your machine requires beforehand.

A genuine OEM sourced replacement deflector shield that is commonly utilized on Craftsman riding lawn mowers and tractors. It is mounted to the side of the deck direct the grass clippings. This part is made from strong durable plastic and it is sold individually. Please note the hardware to secure this deflector shield is sold separately.

This is mulching blade is specially designed for use with Craftsman riding lawn mowers/tractors. Mulching blades are shaped to keep the grass under deck for longer allowing it to be cut into smaller pieces. This provides natural mulch for your lawn since smaller clippings will decompose quicker, releasing their nutrients into the soil. It...Read more is made out of metal and it is sold individually. To install this mulch blade you would need a socket wrench. • Park the riding lawnmower on a flat surface such as a garage floor or a driveway • Disengage blades by pulling the cutting deck lever fully to the disengaged position • Set the riding lawnmower cutting deck to the highest position to access blades • Unscrew the blade bolt • Remove old blade and secure a new one in place • Reassemble in reverse order and test your new blade