9558HN Makita Grinder - Overview

This tapping screw is an authentic hardware that is supplied by original tool manufacturer for use with a variety of Makita power tools. It has multiple uses depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this screw. Note this durable metal screw is sold individually.

This is an OEM Makita authorized replacement part used on variety of Makita Power Tools. This part is sold Individually and it includes the spring. The brush holder in keeps the brushes in place and pushes them against the armature with spring pressure. If the Brush holder is broken or bent it needs to be replaced.

Genuine Makita replacement part. Set of 2 Carbon Brushes with wire lead attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components....Read more Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

This is a genuine Makita replacement part, it is sold individually. Its purpose is to drive the 227505-7 Main Gear. This part is replaced by sliding it on the fan end armature shaft, then securing it to the shaft with the 252186-8 nut. Once you have the Gear Housing apart, this is a good time to make sure the Main Gear has no wear, also check the bearings to make sure they are in good working order.

This switch knob controls the on/off function of the tool, allowing you to start, stop, and lock the tool in operation for continuous use. Made from durable plastic, it is designed to withstand regular wear while maintaining smooth, reliable engagement with the internal switch mechanism. Replacing a worn, cracked, or sticking knob helps restore proper control and ensures consistent, safe operation of your power tool.

Genuine Manufacturer Approved replacement part designed to work with certain Makita Angle Grinders. This part is made out of Metal and it is Sold Individually. This Shoulder Pin is part of the Lock Button Assembly.

This Ball Bearing is shielded on both sides. It is a genuine Makita replacement part and is sold individually. • Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on ...Read morethe tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is a genuine Makita replacement part, it is sold individually. The 233376-2 Spring is part of the spindle lock system on the Grinders shown below. The reason for locking the spindle is so that you can remove and replace grinding wheels. The other parts need for the spindle lock system are part numbers. • 417771-6 Pin cap • 256486-8 Shoulder Pin • And 256486-8 O Ring.

This is a genuine Makita replacement part, it is sold individually. Its is driven by the 227464-5 Drive Gear. Once you have the Gear Housing apart, this is a good time to make sure the Drive Gear has no wear, also check the bearings to make sure they are in good working order.

Genuine Makita replacement part, this item is sold individually. The Pin Cap is part of the spindle lock assembly for the Makita Tool model numbers shown below. When it is pressed it will stop the spindle from rotating, so that a grinding wheel or blade can be removed or installed.

This manufacturer sourced replacement pin is made out rubber and it is sold individually. It acts as a cushion/spacer in a variety of Makita power tools. This is a standard piece of hardware and it has multiple applications based on your tool. Please refer to diagrams for correct application.

This is a genuine Makita replacement part that has been sourced from the original manufacturer to be used with angle grinders and die grinders. The o-ring is commonly used to seat and support the drive gear bearing assembly. This item is sold as an individual replacement part.