936303 (000101) Ariens Lawn Tractor - Overview

This roll pin is a genuine OEM part that is designed for use with various makes and models of snowblowers and lawn tractor snowblower attachments. Made of metal and sold as an individual part, this pin features a 0.25-inch diameter and 1.75-inch length. This pin is hollow and features a split lengthwise down the middle to allow it to fit ...Read morewithin tighter spaces and reduce the movement between two parts, such as the shaft or axle. If your snowblower is not performing well or has seen a decrease in power, check to make sure the roll pin is not damaged. To remove and install a new roll pin, you will need a hammer and a punch, and will simply need to punch out the old pin and punch in the new one.

This OEM-sourced flange bushing supports smooth movement in your lawn equipment by reducing friction. This bearing has an inner diameter of 0.625 inches, an outer diameter of 0.750 inches, a width of 0.5 inches, and a flange diameter of 0.875 inches. Depending on the model and make of your machine, this bushing can be found in various par...Read morets of your machine, such as pivot points, axles, and spindles. A damaged bushing causes increased friction, misalignment, and grinding or squeaking noises. Your machine may need expensive repairs and may eventually fail if you do not replace a broken bushing. To remove an existing bushing, you need to remove components that provide access to the flange bearing. Consult your user manual if needed. Locate the bearing and use a screwdriver or wrench to remove any clips, screws, or bolts securing it. Use a bearing puller tool or a mallet to pull or tap the bearing out of your machine if necessary. Please note that the bushing is sold individually.

This is an authentic OEM part. This key is made of molded plastic and metal and is designed for use with Ariens snowblowers and snow tractors. It is used to start the machine and functions as a safety feature to prevent unauthorized use. This item is sold individually.

This part is sourced directly from the manufacturer, is not part of a kit or assembly, and is sold individually. The Bushing is made of durable black rubber and is usually found on the fuel tank. Through regular use, the Bushing may become worn, damaged, or dried out, at which point it will need to be replaced. Customers rate this repair as Easy.

This genuine OEM lock nut is designed for use with Ariens snow blowers and throwers. It helps secure the skid shoe runner to the deck and is engineered to resist loosening when properly threaded onto a bolt, ensuring a stable and reliable connection. Made from durable metal, this high-quality part is sold individually. For safe installation, be sure to use a properly sized wrench.

This tension spring, also known as a coil spring or extension spring, is an authentic manufacturer replacement part used in a variety of outdoor power equipment. It is a cylindrical, steel spring with one hook/ring on each end, which is used to hook on to the equipment parts. The spring is responsible for providing tension or resistance t...Read moreo various parts for controlled movement and added stability. It is typically located in areas such as throttle controls, idler pulleys, and belts. The tension spring can rust or break over time, leading to loose components, equipment instability, and potentially causing damage. To remove and replace the tension spring, use needle nose pliers or a spring hook tool to grab the hooks and gently pry them off. Hook the new spring on the attachment points and ensure that it can maintain the required tension.

This OEM part is a zerk fitting that is sometimes called a grease fitting, lube fitting, grease zerk, or Alemite fitting. It is a metal nipple that you connect a grease gun to, allowing you to lubricate the moving parts in your lawn equipment, usually on joints or bearings. This fitting is 1/4 inch wide, has 28 threads per inch, and a thr...Read moreeaded portion that is .256 inches long. If the fitting is broken, you may notice that your machine is moving sluggishly, or the fitting may appear cracked or clogged with debris. It is important to replace a damaged fitting right away, because if you do not, debris can prevent the fitting from accepting grease and the moving parts of your machine will wear out faster and eventually break down completely. To replace the fitting, you will need to use a wrench to remove it from your machine. Keep in mind that this replacement part is sold separately, so you may want to consider stocking up on fittings before you need them. Since the fittings on your machine wear out at the same rate, having a few extra on hand can save you time and hassle down the road.

This is a manufacturer-approved carriage bolt designed for use with Ariens snow blowers and snow throwers. Made from durable metal, this standard hardware component is suitable for a variety of applications. The bolt features a square section beneath the rounded head, which fits securely into a matching square hole in the workpiece. This ...Read moredesign prevents the bolt from turning when the nut is tightened, ensuring a secure and stable fit. Sold individually, this bolt is a reliable replacement part. For proper installation and compatibility, please refer to your equipment’s diagrams or user manual.