926011 (000500) Ariens Snow Blower - Overview

This OEM-verified shear bolt, measuring 2-1/8 inches in length and 5/16 inches in diameter, is designed to break under excessive force to protect your lawn equipment by absorbing the impact. Specifically, it allows the augers of your machine to stop while the shaft and gear case continue to rotate. To check if the shear bolt is broken, in...Read morespect it for fractures or missing pieces. You might notice that the shaft of your machine is rotating normally but the augers are not moving with it. It is important to address a damaged shear bolt promptly to avoid costly repairs or equipment failure. To remove the shear bolt from your machine, use a wrench or socket to turn it counterclockwise. As this replacement part is sold individually, it is strongly recommended that you keep spare bolts on hand in the event that they break.

The Friction Wheel is part of the clutch assembly, which helps to drive your unit. If broken from being worn down, you will have drivability problems and should replace the part. This part is metal with a rubber outer ring, and comes in white/black. Installation will require a wrench set, socket set, and pliers and is rated as "Medium" di...Read morefficulty by customers. Refer to your make, model and diagram to check if this is the right part for you.

This shear bolt and nut, also known as the shear bolt assembly, is sourced from the original manufacturer, and it is guaranteed to fit your snowblower. Each assembly includes one metal shear bolt and one metal nut, located at the connection point between the auger and gearbox/shaft. It is a safety mechanism designed to protect the snowblo...Read morewer auger from damage caused by sudden stops or excessive resistance. When the auger encounters a blockage or excessive load the shear bolt will break thereby preventing more severe damage to the gearbox. Once the bolt is sheared, it will need to be replaced. The bolt will also need to be replaced if it is bent or worn down, as a faulty shear bolt can result in damage to the auger, gearbox, and motor, as well as reduced equipment ability to throw snow, and increased safety risks. Use a socket or wrench to unthread the nut and remove the broken shear bolt. Align the new shear bolt with the mounting hole and secure it with the new nut. Note that this is a common repair and it is best to have several spare shear bolts and nuts on hand.

The Runner is a 6 x 3.5 inch, orange, metal part which is used to allow the snowblower to glide smoothly on the ground. It's installed using a wrench or socket, and its installation has been rated "Easy" by customers. If broken, the auger housing will drag on the ground and the part should be replaced. Refer to your make, model and diagram to ensure this is the correct part.

The Snap Clip is a silver, metal part used to prevent the wheels from falling off, by securing it to the axle. If broken or damaged it should be replaced, or the wheel may fall off.

This is a genuine OEM sourced part which is specially designed for use with Ariens snowblowers. It provides an identical replacement for a missing or a damaged fitting that was installed on a new unit. This is a standard hardware which may have multiple applications. Please make sure to check the owners manual and the appropriate diagrams...Read more for the correct location and application of this component. Keep in mind this high-quality fitting is made of durable metal and is sold individually.

This genuine manufacturer-sourced component which is specially made for use with Ariens snowblowers. The key helps to secure the gear on the axle, unfortunately, over time it may wear out, get damaged or lost eventually requiring a replacement. Please make sure to refer to the appropriate diagrams of your model for the correct location an...Read mored application of this hardware. Keep in mind this high-quality item is made of durable metal and is sold individually.

This roll pin is a genuine OEM part that is designed for use with various makes and models of snowblowers and lawn tractor snowblower attachments. Made of metal and sold as an individual part, this pin features a 0.25-inch diameter and 1.75-inch length. This pin is hollow and features a split lengthwise down the middle to allow it to fit ...Read morewithin tighter spaces and reduce the movement between two parts, such as the shaft or axle. If your snowblower is not performing well or has seen a decrease in power, check to make sure the roll pin is not damaged. To remove and install a new roll pin, you will need a hammer and a punch, and will simply need to punch out the old pin and punch in the new one.

It is a genuine OEM sourced replacement part, it is specially designed for use with Ariens snowblowers. This spring clip pin has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this hardware. Note this durable metal item is sold individually.

This chute control update kit is designed to improve the rotation and directional control of the discharge chute on snow blowers. Featuring durable metal components, it replaces older cable systems for smoother, more precise adjustments. The kit includes a gear, cable, and hardware such as springs and bushings, along with installation ins...Read moretructions for easy setup. Installation involves removing the existing components and securing the new parts according to the provided guide.

This flange split bushing is a genuine OEM part used to add stability and reduce friction damage between rotating parts, such as drive shafts and gears, in a variety of outdoor power equipment. The bushing has an outside diameter of 1 1/3 inches and an inner diameter of 1 inch, as well as a flange on one end which prevents the bushing fro...Read morem moving during use. It is made of nylon which is a type of material known for its resistance to wear, and ability to self-lubricate. The bushing is split along its length, for easy removal and installation. The bearing may become damaged if it is inadequately lubricated, or from continuous exposure to heat and chemicals. If you notice that your equipment is excessively noisy, shaking, and difficult to maneuver, you will need to replace the bushing promptly to prevent damage to the equipment. Remove the fasteners that secure the bushing and use a bearing puller to detach the old bushing. Place the new bushing in position and secure it in place.