924328 (000101) Ariens Snow Blower - Overview

This OEM-verified shear bolt, measuring 2-1/8 inches in length and 5/16 inches in diameter, is designed to break under excessive force to protect your lawn equipment by absorbing the impact. Specifically, it allows the augers of your machine to stop while the shaft and gear case continue to rotate. To check if the shear bolt is broken, in...Read morespect it for fractures or missing pieces. You might notice that the shaft of your machine is rotating normally but the augers are not moving with it. It is important to address a damaged shear bolt promptly to avoid costly repairs or equipment failure. To remove the shear bolt from your machine, use a wrench or socket to turn it counterclockwise. As this replacement part is sold individually, it is strongly recommended that you keep spare bolts on hand in the event that they break.

The Friction Wheel is part of the clutch assembly, which helps to drive your unit. If broken from being worn down, you will have drivability problems and should replace the part. This part is metal with a rubber outer ring, and comes in white/black. Installation will require a wrench set, socket set, and pliers and is rated as "Medium" di...Read morefficulty by customers. Refer to your make, model and diagram to check if this is the right part for you.

The Runner is a 6 x 3.5 inch, orange, metal part which is used to allow the snowblower to glide smoothly on the ground. It's installed using a wrench or socket, and its installation has been rated "Easy" by customers. If broken, the auger housing will drag on the ground and the part should be replaced. Refer to your make, model and diagram to ensure this is the correct part.

This traction drive v-belt is a genuine replacement part. It is supplied directly from original equipment manufacturer for use with Ariens lawn and garden equipment. This is the main drive belt that helps to drive the equipment. To ensure correct applications please make sure to check appropriate diagrams. When replacing a belt it is advi...Read moresed to clean the pulleys before installing the new belt. This will help to ensure top performance and longevity with your new belt. This part is made out of rubber material and it is sold individually. To complete this repair you will need a set of wrenches.

This roll pin is a genuine OEM part that is designed for use with various makes and models of snowblowers and lawn tractor snowblower attachments. Made of metal and sold as an individual part, this pin features a 0.25-inch diameter and 1.75-inch length. This pin is hollow and features a split lengthwise down the middle to allow it to fit ...Read morewithin tighter spaces and reduce the movement between two parts, such as the shaft or axle. If your snowblower is not performing well or has seen a decrease in power, check to make sure the roll pin is not damaged. To remove and install a new roll pin, you will need a hammer and a punch, and will simply need to punch out the old pin and punch in the new one.

This chute gear in your snowblower is a plate-like part found in the discharge chute crank mechanism. It is responsible for controlling the movement of the chute, allowing you to direct the snow being discharged. The gear attaches to the chute and is rotated by a pinion gear. If the chute gear is broken, you may notice chipped or missing ...Read moreteeth on the gear. It may also have difficulty rotating smoothly or become stuck, making it challenging or impossible to adjust the chute. To remove the chute gear, you will need a socket and a screwdriver. Start by removing the gear cover, which is typically secured with screws. Once the cover is removed, you will have access to the chute gear assembly. Remove any necessary components until the chute gear is free to be lifted off its shaft. When replacing the chute gear, it is important to note that it is sold separately from any accompanying hardware or fasteners.

This OEM-sourced flange bushing supports smooth movement in your lawn equipment by reducing friction. This bearing has an inner diameter of 0.625 inches, an outer diameter of 0.750 inches, a width of 0.5 inches, and a flange diameter of 0.875 inches. Depending on the model and make of your machine, this bushing can be found in various par...Read morets of your machine, such as pivot points, axles, and spindles. A damaged bushing causes increased friction, misalignment, and grinding or squeaking noises. Your machine may need expensive repairs and may eventually fail if you do not replace a broken bushing. To remove an existing bushing, you need to remove components that provide access to the flange bearing. Consult your user manual if needed. Locate the bearing and use a screwdriver or wrench to remove any clips, screws, or bolts securing it. Use a bearing puller tool or a mallet to pull or tap the bearing out of your machine if necessary. Please note that the bushing is sold individually.

This OEM flange bearing in your lawn equipment supports smooth movement in the gear case and impeller. It reduces friction and ensures stability for rotating components like gears or impeller shafts. If the flange bearing is damaged, you may hear grinding or squeaking sounds, and it may show signs of cracks, wear, or deformation. Neglecti...Read moreng a broken flange bearing can lead to additional damage to the gear case and impeller assembly, potentially causing equipment failure. To remove a faulty bearing, turn the machine off and disconnect it from any power source. Remove any covers, guards, or components that provide access to the gear case and impeller assembly. This may involve loosening screws, bolts, or clips. Consult your user manual to locate the flange bearing. Use a screwdriver or wrench to remove any fasteners that secure the flange bearing before detaching the bearing itself. Please note that this flange bearing is sold individually and does not include any accompanying hardware.

The ball bearing goes next to the bearing flange and is made of metal. Keep in mind this high-quality part is priced individually. It is a genuine item that is supplied by the original equipment manufacturer for use with Ariens snowblowers. During replacement, it may require a socket set to help install this part correctly. It will require replacing if it breaks.

It is a genuine high quality seal that is supplied from original equipment manufacturer for use with Ariens snowblowers. This is one of the seals for the gearcase, please make sure to check appropriate diagrams for correct location and use of this hardware. One durable rubberized metal seal is included per order.