924104 (001400) Ariens Snow Blower - Overview

This OEM-verified shear bolt, measuring 2-1/8 inches in length and 5/16 inches in diameter, is designed to break under excessive force to protect your lawn equipment by absorbing the impact. Specifically, it allows the augers of your machine to stop while the shaft and gear case continue to rotate. To check if the shear bolt is broken, in...Read morespect it for fractures or missing pieces. You might notice that the shaft of your machine is rotating normally but the augers are not moving with it. It is important to address a damaged shear bolt promptly to avoid costly repairs or equipment failure. To remove the shear bolt from your machine, use a wrench or socket to turn it counterclockwise. As this replacement part is sold individually, it is strongly recommended that you keep spare bolts on hand in the event that they break.

The Friction Wheel is part of the clutch assembly, which helps to drive your unit. If broken from being worn down, you will have drivability problems and should replace the part. This part is metal with a rubber outer ring, and comes in white/black. Installation will require a wrench set, socket set, and pliers and is rated as "Medium" di...Read morefficulty by customers. Refer to your make, model and diagram to check if this is the right part for you.

The Runner is a 6 x 3.5 inch, orange, metal part which is used to allow the snowblower to glide smoothly on the ground. It's installed using a wrench or socket, and its installation has been rated "Easy" by customers. If broken, the auger housing will drag on the ground and the part should be replaced. Refer to your make, model and diagram to ensure this is the correct part.

This roll pin is a genuine OEM part that is designed for use with various makes and models of snowblowers and lawn tractor snowblower attachments. Made of metal and sold as an individual part, this pin features a 0.25-inch diameter and 1.75-inch length. This pin is hollow and features a split lengthwise down the middle to allow it to fit ...Read morewithin tighter spaces and reduce the movement between two parts, such as the shaft or axle. If your snowblower is not performing well or has seen a decrease in power, check to make sure the roll pin is not damaged. To remove and install a new roll pin, you will need a hammer and a punch, and will simply need to punch out the old pin and punch in the new one.

This OEM-sourced flange bushing supports smooth movement in your lawn equipment by reducing friction. This bearing has an inner diameter of 0.625 inches, an outer diameter of 0.750 inches, a width of 0.5 inches, and a flange diameter of 0.875 inches. Depending on the model and make of your machine, this bushing can be found in various par...Read morets of your machine, such as pivot points, axles, and spindles. A damaged bushing causes increased friction, misalignment, and grinding or squeaking noises. Your machine may need expensive repairs and may eventually fail if you do not replace a broken bushing. To remove an existing bushing, you need to remove components that provide access to the flange bearing. Consult your user manual if needed. Locate the bearing and use a screwdriver or wrench to remove any clips, screws, or bolts securing it. Use a bearing puller tool or a mallet to pull or tap the bearing out of your machine if necessary. Please note that the bushing is sold individually.

This OEM flange bearing in your lawn equipment supports smooth movement in the gear case and impeller. It reduces friction and ensures stability for rotating components like gears or impeller shafts. If the flange bearing is damaged, you may hear grinding or squeaking sounds, and it may show signs of cracks, wear, or deformation. Neglecti...Read moreng a broken flange bearing can lead to additional damage to the gear case and impeller assembly, potentially causing equipment failure. To remove a faulty bearing, turn the machine off and disconnect it from any power source. Remove any covers, guards, or components that provide access to the gear case and impeller assembly. This may involve loosening screws, bolts, or clips. Consult your user manual to locate the flange bearing. Use a screwdriver or wrench to remove any fasteners that secure the flange bearing before detaching the bearing itself. Please note that this flange bearing is sold individually and does not include any accompanying hardware.

It is a genuine high quality seal that is supplied from original equipment manufacturer for use with Ariens snowblowers. This is one of the seals for the gearcase, please make sure to check appropriate diagrams for correct location and use of this hardware. One durable rubberized metal seal is included per order.

This is an authentic Ariens replacement part that has been sourced from the original manufacturer to be used with snowthrowers. The metal spring is used to link the control and the idler pulley arm to allow the cable to engage the idler to drive the traction control. This item is available as an individual replacement part.

This L-3 synthetic severe-duty gear lube is specially produced for use on Ariens snow blowers. It is used to lubricate gearbox gears that help to drive the unit. This is an authentic OEM sourced item that is sold individually.

This is a genuine Ariens replacement part that has been sourced from the original manufacturer to be used with snowthrowers. The metal bushing fits into the bearing support to provide spacing between the rake shaft and the support. The bushing is sold as an individual replacement part.

It is a genuine OEM sourced part that is designed for use with Ariens snow blowers and lawn tractors. This is a special component that helps to secure the bearing. It is a high-quality replacement for a faulty or a missing bearing flange that was installed on a new unit. To ensure the exact location and the correct installation of this ha...Read morerdware make sure to check the appropriate diagrams of your model. This authentic bearing flange is made of durable metal and is sold individually.