9227 - Overview

This cord guard is a genuine Makita replacement part, and it is a direct replacement for a damaged or missing cord guard. Power tool cords undergo a lot of stress, and these cord guards help to alleviate some of that stress at the weakest point--right where the cord enters the tool. Over time cord guards will deteriorate and eventually re...Read morequire replacement. Keeping a strong cord guard on your tool will help will cord life. This cord guard is compatible with the tools listed below, but it is not guaranteed to fit any other power tools.

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls re...Read moreduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

The pin cap attaches to the compression spring and is made of plastic. This part is an OEM from Makita for use in grinders, sanders, and polishers. A set of pliers might be necessary during the installation of this item. Over time this part may break and will need to be replaced. This item is available as an individual replacement part.

This is a Genuine OEM replacement part used on Makita Power Tools. This item is made out of Plastic and it is Sold Individually. The purpose of the Brush Cap is to retain the Brushes in the Brush Holders. This Brush Cap has external threads that thread into the housing of the tool. Be careful when removing and replacing these, they have a tendency to break.

This set of two carbon brushes is a genuine Makita replacement part, packaged in an official Makita retail box. Each brush includes wire leads and attached brush springs, and is designed to restore optimal performance in compatible Makita tools. Carbon brushes are among the most commonly replaced components in power tools, as they gradual...Read morely wear down through friction and regular use. Worn brushes can lead to intermittent motor function, reduced power, or diminished electric braking. Replacing them can resolve these issues and restore proper motor performance. Signs of wear include brushes worn near the wire lead, or those that are cracked, pitted, or burned. When replacing carbon brushes, it’s also important to inspect the armature for any signs of damage, such as burns or cracks, which may indicate a more serious motor issue.

• This cord guard is a genuine Makita replacement part and is sold individually. • Cord guards, also called cord protectors, are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard. ...Read more • This cord guard will fit cords for the tools listed under the "Compatible Tools" listing. It is not guaranteed to fit any other cords.

This pan head screw is an authentic replacement part. It is sourced directly from original equipment manufacturer for use with Makita power tools. This standard hardware is used in different locations depending on equipment. To ensure correct application please make sure to check appropriate diagrams. Includes one (1) metal screw. You will need a torx or a flat-head screwdriver to tighten or loosen this screw.

This replacement hardware is a genuine OEM sourced part, it is not an aftermarket imitation. It is a commonly used with Makita power tools. This standard hardware has multiple applications depending on the tool. Please refer to appropriate diagrams for correct location and use of this screw. It is a pan head screw which is sold individual...Read morely. You will need a Phillips head screwdriver to install or remove this hardware.

This is a genuine Makita replacement tapping screw. It is sourced directly from original equipment manufacturer for use with a variety of power tools. This hardware has multiple uses depending on your tool. Please make sure to check appropriate diagrams for correct location and application of this item. This pan-head tapping screw is sold individually. You will need a screwdriver to install or remove it.

This is an authentic manufacturer sourced replacement part used on Makita sanders/polishers. Switch is an important part of the tool which handles on/off operations. Because switches use mechanical internals, they will tend to wear out over time, eventually requiring replacement. It has a plastic body and it is sold individually. To repl...Read moreace this switch you would need a Screwdriver. • Remove screws used to hold two pieces of housing set together • Disconnect wires from the old switch and remove it from the housing • Place the new switch in the housing and connect wires to it • Reassemble the housing

This is a manufacturer approved replacement part designed for Makita grinders/sanders. This is the side handle 36 that provides a safe and stable grip for your tool. It is made out of plastic and metal. It is sold individually. No tools are needed to replace this grip. Simply screw in the grip/handle into threaded opening on the housing.