919153532 Craftsman Compressor - Overview

Introducing Craftsman's high-quality relief valve. The vale is intricately designed to regulate and control pressure in your Craftsman appliance effortlessly. Made with superior materials for longevity and optimum performance this relief valve is the perfect replacement part for keeping your appliance in top condition. It flawlessly suits...Read more a host of Craftsman models ensuring a secure and snug fit. Discover the ease of maintenance with this Craftsman relief valve for superior appliance functionality. Keep your appliance running smoothly and efficiently with this robust and reliable component.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling • The O-ring has ragged, tattered edges. Thes...Read moree are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion • One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression • The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening • The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking • The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

This is an authentic OEM part. The filter is used with air compressors from Porter Cable, DeVilbiss, and Black & Decker. The foam filter is used to prevent dirt and debris from entering and potentially damaging the pump. A hex driver, or screwdriver may be needed to install this item and it is sold individually.

This is an authentic OEM part for use with Craftsman Compressors. The check valve lets pressurized air flow into the tank and prevents air from flowing back into the pump. A failed check valve will apply high air pressure to the head of the pump preventing the motor from restarting once the tank has filled. The most common reason for repl...Read moreacing the check valve is if the motor starts with an empty tank but won't start when the tank is full. This part is sold individually. The tool that you will need to replace the check valve is an adjustable wrench and Teflon tape.

This is an authentic replacement part that has been OEM sourced to be used with Porter Cable, DeVilbiss, and Black and Decker air compressors. The metal nut is commonly used to connect the outlet tube to the cylinder head assembly. This item is available as an individual replacement part, a hex wrench is needed for this repair.

This is a genuine replacement part manufactured for use with air compressors from DeWalt. This part creates an airtight seal between the elbow and the tube. You may need a wrench to replace this part. This assembly but sleeve is sold individually and made of metal.

This safety valve is a genuine replacement part manufactured for use with air compressors. If the compressor's pressure switch malfunctions and does not turn the motor off when the amount of pressure is met, the safety valve will open to release the extra air pressure. The amount of pressure required to open the safety valve is set by the...Read more tension of the spring inside the valve. The spring can wear out, and leave the valve open at a lower pressure than what is set to turn the switch off, and will not allow pressure to build inside the tank. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality part is made of durable metal and is sold individually.

Used to secure the wheels on a compressor or generator, this Shoulder Bolt is roughly 3.75 inches long and is sourced directly from the original equipment manufacturer. It is made of dark grey metal, is not part of a kit or assembly, and is sold individually. This part needs to be replaced when it is damaged or worn and may cause the w...Read moreheel to fall off if it breaks. You will need a wrench or socket to complete this repair. Customers rate this repair as Easy.