9115-0-675020 Craftsman Generator - Overview

This is an OEM replacement part and is sold individually. Its propose is to deliver an electric current from an ignition system to the combustion chamber of a gas fueled engine. It will ignite the air fuel mixture by the spark. Spark Plugs will usually have to gapped to the manufactures specifications found in the owners manual. Over tim...Read moree a Spark Plug will become fouled because the air/fuel ratio may be set wrong,worn piston rings, carbon build up and other factors. It is better to replace a fouled spark plug, rather then trying to clean it.

This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine...Read more. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.

This rewind starter spring or as it is also known, recoil spring, rewinds the pull robe back into the starter housing of your engine. The spring is made of metal, silver colored, and sold individually. Over time, you may notice that you are having trouble retracting your pull cord, which could be a symptom of the rewind starter spring f...Read moreailing due to fatigue or wear. Replacing this part is a repair our customers found easy. Locate and replace the start spring inside the starter housing; no special tools are required for this job.

This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.

The cylinder head gasket, also known just as the head gasket, is an OEM part sold individually. Grey in color, the head gasket provides a seal between the cylinder head and the engine block in your engine. Over time, it can become damaged due to wear. You may also need to replace this part any time you have had to remove the cylinder hea...Read mored for any other reason, as the gasket is a one time use. If you suspect your head gasket is damaged, perform a compression test. In doing so, you may hear air escaping from the head gasket area, and you will know this part is responsible. Symptoms that can be exhibited if this part needs replacing include an engine lacking power. Most of our customers thought this was a medium-difficulty repair. The repair requires a wrench or sockets and a torque wrench. When re-installing your head gasket, torque in an alternating patter to the manufacturer specifications for a proper seal.

This magneto, also known as an ignition coil, is a genuine OEM replacement part for outdoor power equipment. It generates the spark needed to ignite the air-fuel mixture in the engine’s combustion chamber, ensuring smooth and reliable operation. Over time, the magneto may fail due to worn wiring, damage to the spark plug lead, or incorrec...Read moret gapping between the coil and flywheel. Symptoms of a faulty magneto include misfiring, hard starting, and poor performance. Installation involves removing the spark plug for safety, accessing the flywheel, and setting the correct gap with a feeler gauge before securing the new part.

This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should be replaced. Installation is rated as "Medium" difficulty by customers, and will require a screwdriver, wrenchset and seal puller. Refer to ...Read moreyour make, model and diagrams to ensure you've chosen the correct part. This model comes in black and grey.

This is an authentic manufacturer sourced replacement part designed for use with a variety of lawn and garden equipment. This carburetor intake gasket which provides an air tight seal for the carburetor. Over time gaskets tend to deteriorate and would need to be replaced. It is made out of compound material and it is sold individually. You would need a screwdriver to replace this item.

The Crankcase Gasket (.015) is a manufacturer-certified part which is rated as being "Medium" difficulty to install. It will require a screwdriver, socket set, wrench set, and nut driver. It s used to provide an air seal between the crankcase and the cylinder assembly. If broken, there will be oil leaking, and the part should be replaced....Read more Refer to your make, model and diagrams to check if this is the right part for you. This part is made of a composite of materials, and comes in gray.

The Breather Gasket is OEM and used to provide an airtight seal for the breather assembly. It is a gray part, attached between the breather cap and engine. Installation is rated "Easy" and will require a wrench set and socket set. If broken, damaged, or worn due to fatigue, there may be oil leaking from it, and the engine may be running r...Read moreough from an unwanted vacuum sucking in air. If this happens, replace the part. Refer to your make, model and diagrams to ensure this is the correct part for you.