Models > 911361

911361 - Overview

Models starting with 911361

Exact Part matches for your search term

[Viewing 1 of 1]
GROMMET STRIP – Part Number: 911361
GROMMET STRIP
This part number matches the current model number 911361
PartSelect #: PS1297471
Manufacturer #: 911361
  No Longer Available
Keep searches simple, eg. "belt" or "pump".
Light Bulb - 40W – Part Number: 40A15
Light Bulb - 40W
★★★★★
★★★★★
(6)
PartSelect #: PS217532
Manufacturer #: 40A15
$9.42
  In Stock
Hinge with Roller - Right Side – Part Number: WB14X104
Hinge with Roller - Right Side
★★★★★
★★★★★
(10)
PartSelect #: PS231612
Manufacturer #: WB14X104
This is a hinge with roller for the oven door on your range. The roller allows you to open and close the door with ease and control. If your door is not opening easily, you may need to replace this pa...
$50.55
  In Stock
Hinge with Roller - Left Side – Part Number: WB14X103
Hinge with Roller - Left Side
★★★★★
★★★★★
(4)
PartSelect #: PS231611
Manufacturer #: WB14X103
This is known as a hinge with roller and it is for the oven door of your range. The hinge with roller allows you to easily open and close your oven door without much effort. Take note that your applia...
$51.16
  In Stock
Gas Range Drip Pan – Part Number: WB31K5026
Gas Range Drip Pan
★★★★★
★★★★★
(3)
PartSelect #: PS244259
Manufacturer #: WB31K5026
This chrome drip pan is sold individually.
$27.03
  In Stock
Screw – Part Number: WB1M1
Screw
★★★★★
★★★★★
(1)
PartSelect #: PS234320
Manufacturer #: WB1M1
Sold Individually.
$6.46
  In Stock
Screw – Part Number: WB1X1130
Screw
★★★★★
★★★★★
(2)
PartSelect #: PS234427
Manufacturer #: WB1X1130
Sold Individually.
$6.68
  In Stock
SCREW-10AB – Part Number: WB1X1137
SCREW-10AB
PartSelect #: PS234434
Manufacturer #: WB1X1137
$6.68
  In Stock
ANTI-TIP RANGE KIT – Part Number: WB2X7909
ANTI-TIP RANGE KIT
PartSelect #: PS242777
Manufacturer #: WB2X7909
$39.67
  In Stock
CLIP – Part Number: WB2X9105
CLIP
PartSelect #: PS243383
Manufacturer #: WB2X9105
  No Longer Available
Leveling Screw – Part Number: WB1M18
Leveling Screw
PartSelect #: PS234327
Manufacturer #: WB1M18
Sold Individually.   No Longer Available
Light Switch – Part Number: WB24X415
Light Switch
★★★★★
★★★★★
(1)
PartSelect #: PS237171
Manufacturer #: WB24X415
$36.29
  In Stock

Common Symptoms of models starting with 911361

[Viewing 2 of 2]
Door won’t close
Fixed by
these parts
Show All
Door won’t open after self cleaning cycle
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The right side hinge assembly broke. Replaced both sides
First I removed the door by lifting it off the hinge assemblies.

Then I removed the drawer to access the spring.

Removed the spring, noting which attachment hole was used.

Removed the hinge assembly with a Phillips screwdriver.

Replacef the unit.

Repeated for the other hinge assembly.

Note: it took longer to find the correct parts in the parts diagrams than it did to replace them.
Parts Used:
Hinge with Roller - Right Side Hinge with Roller - Left Side
  • Frank from Pebble Beach, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
43 of 45 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven door hinge rollers broke, hard to open door
Before removing screws, I reached in and felt for where the upper end of the spring attached to the hinge. There are three holes in the end of the hinge arm, so I wanted to be sure of which hole to use. (The holes are very close together, so if the spring falls out before you determine which hole it was in, it probably won't matter so long as you are sure to use the same hole on both new hinges.) I then removed three Phillips screws per hinge. Once the hinge was loose, I could wiggle it around and release enough of the spring tension to slip the top end of the spring out of the hole on the hinge arm. Then I pulled out the old hinge and inserted the new one and replaced the three screws. Without the tension, the lower end of the spring fell out of the little hole in the oven bottom where it normally attaches. Our gas oven has a broiler rather than a storage drawer, so it was a little difficult to get the lower tip of the spring back into that hole. It actually ended up being easier to get the lower tip of the spring back into that hole first, before trying to reattach it to the hinge arm. Once I got the lower end into that hole, I pulled up on the spring and maintained upward pressure on the spring while I fiddled around to get the upper end into the hinge arm hole. Took about 20 minutes, door works perfectly now. Lots of sharp edges inside the oven, so had to be careful.
Parts Used:
Hinge with Roller - Right Side Hinge with Roller - Left Side
  • Peter from Framingham, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
16 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Failed oven door hinge
Pull oven door open about a couple of inches. Grab the door by the sides and pull up to remove from the hinges. Set it aside. Remove the storage drawer under the oven. This gives you access to the tension spring attached to the hinge. Detach it by hand. Using a phillips head, unscrew and remove the damaged hinge. Replace the new hinge. Reattach the spring. Replace the storage drawer. Replace the oven door. Done.
Parts Used:
Hinge with Roller - Left Side
  • Jack from Spencerport, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
16 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!