Models
>
91132224100
91132224100 Kenmore Cooktop - Overview
Sections of the 91132224100
[Viewing 2 of 2]
Keep searches simple, eg. "belt" or "pump".
Grate Foot
PartSelect #: PS2353327
Manufacturer #: WB02T10461
The Grate Foot is a black rubber part which attaches underneath the grate in order to protect your stovetop from being scratched, which it does by cushioning the grate on your gas range. If this part ...
$12.51
In Stock
Spark Igniter
PartSelect #: PS11736298
Manufacturer #: WB13X27058
Also known as spark electrode. This part helps your burner ignite and produce flame.
$63.66
In Stock
Top Electrode Mounting Clip
PartSelect #: PS3510420
Manufacturer #: WB01K10112
Sold individually.
$13.71
In Stock
Screw
PartSelect #: PS271689
Manufacturer #: WH2X930
This screw is sold individually.
$12.22
In Stock
Burner Spark Module - 120V 60Hz
PartSelect #: PS231281
Manufacturer #: WB13K25
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
No Longer Available
Gas Pressure Regulator
PartSelect #: PS2337785
Manufacturer #: WB19T10078
This comes set from the manufacturer for Natural Gas. It also includes the conversion to Liquid Propane.
This valve automatically cuts off the flow of gas at a certain pressure.
$54.42
In Stock
LP Orifice - Center
PartSelect #: PS1020519
Manufacturer #: WB28K10288
This orifice spud changes the burner from natural gas, to liquid propane. This orifice is sold individually. Size: .74mm
$8.54
In Stock
Questions And Answers for 91132224100
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 91132224100
[Viewing 3 of 3]Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Top four burners on oven would not light without using match
Really simple..Opened the top of the oven and followed the four wires hooked to the igniters on the burners to the back of the oven. Unscrewed top section in back of oven. Found spark module screwed to uppper back of oven on right side. Used a nutdriver to take a few screws out of upper back of oven. Unscrewed spark module from oven. Ther
... Read more
e are six wires - four to the burners and two to the power supply....Wires are attached by connectors so didn't have to do anything but pull the connectors off the old spark module one at a time and push them onto the new spark module matching postion of each wire. Screwed spark module back onto back of oven. Screwed back section of oven back onto rear of oven, and that was it. Works perfectly. Saved more than $100 for service call and whatever elevated price they'd charge me for the spark module.
Read less
Parts Used:
-
David from Logansport, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
62 of 77 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner wouldn't light
I removed the old igniter by working a thin screwdriver under the edge of the igniter, and carefully prying it up. I then used pliers to pull off the electrical wire. Connected up the new igniter, and pushed it back into the hole. A very simple repair.
I've replaced 2 igniters on this stove. My symptoms were that when I tried ... Read more to light one of the bad burners I heard clicking, and could see the spark on the other (working) burners. So I knew the basic sparking function was working. Just that the igniter on the broken burner would not spark.
I've replaced 2 igniters on this stove. My symptoms were that when I tried ... Read more to light one of the bad burners I heard clicking, and could see the spark on the other (working) burners. So I knew the basic sparking function was working. Just that the igniter on the broken burner would not spark.
Read less
Parts Used:
-
Jeffrey from Freehold, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
50 of 59 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Grate Foot had worn out
A rubber grate foot on my range top had worn out. I pulled the worn foot out and installed the new grate foot with no tools or accessories. Good as new! Now I don't have to worry about the grate scraping my range top and scratching the paint. I also ordered extras so I won't have to wait if another wears out.
Parts Used:
-
Kathryn from Star City, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
24 of 30 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!