9067-2 Generac Generator - Overview

Hard starting or an engine that suddenly stops may point to a damaged magneto armature. This ignition coil turns magnetic energy from the spinning flywheel into the electrical pulse that fires the spark plug. First try a known-good spark plug and inspect the safety switches, grounding wire, terminals, and flywheel magnet. Confirm fit from...Read more the full engine identification numbers, since similar coils may mount differently. Work only with the engine off and cool. Disconnect the battery and spark plug lead before removing covers. During installation, use the air gap listed in the service manual and tighten the mounting screws evenly. Keep hands clear of the flywheel and use an insulated tester to check for spark.

This is a manufacturer approved starter pinion gear designed for use with lawn and garden equipment engines. This Starter pinion gear is attach to the starter clutch drive and engages the flywheel to start the engine. It is made out of Plastic and Aluminum and it is Sold Individually.

This is an original part from Briggs & Stratton. The rocket cover gasket is compatible with many small engines. The cardboard composite gasket is designed to prevent damage to engine parts and absorb fuel leakage. A screwdriver and a wrench may be needed to make the removal and replacement. This part is sold individually. It is recommended to refer to engine manual and diagrams for further instruction.

This is an authentic manufacturer-sourced replacement part which is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is an identical replacement for a missing or damaged seal that was originally installed on a new unit, please make sure to check the appropriate diagrams of you...Read morer model for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable rubber and is sold individually.

It is an authentic manufacturer sourced replacement part that is specially designed for use with Briggs and Stratton engines installed on generators and lawn and garden equipment. This gasket provides an air tight seal between the carburetor and the manifold. Over time gaskets tend to deteriorate and crack eventually requiring replacement. It is made out of high-quality composite material and it is sold individually.

This is a genuine manufacturer-approved replacement part which is specially designed for use on Briggs and Stratton engines commonly installed on lawn and garden equipment. The push rod rides on the camshaft to push the exhaust valve open during the exhaust stroke. A bent rod can not only affect your engine's performance, it can seriously...Read more damage other parts if the problem is not taken care of immediately. Keep in mind this high-quality part is made of durable metal and is sold individually.

This is an authentic OEM component from Briggs & Stratton. The cylinder head gasket is compatible with many small engines, and is sold individually. The cardboard composite gasket is fitted onto the cylinder head, providing protection from friction and leaks. A wrench is needed for the repair. This item is also included with the valve gasket set (808392).

This spark plug terminal is supplied directly from the original equipment manufacturer. The metal terminal is designed to fasten the spark plug to the engine lead wire. This component is sold individually, and needle nose pliers are helpful with the repair. Please refer to the appropriate diagrams of your engine model for the proper application of this hardware.

The valve tappet attaches to the push rod. It is made out of metal and is sold individually. This is a Briggs & Stratton and Toro replacement part directly sourced from the manufacturer for use in engines. It may require a set of pliers during installation. This part may become broken and will need to be replaced.

This sealing washer is a genuine OEM replacement designed for small engine valve or rocker covers. It provides a tight, leak-free seal around the valve cover fasteners, helping prevent oil seepage and maintaining proper engine lubrication and cleanliness. Manufactured to exact OEM specifications for a precise fit and long-term durability,...Read more it’s an ideal replacement when worn or hardened washers lead to oil leaks, reduced engine reliability, or messy buildup around the valve cover.

This is an authentic Briggs & Stratton replacement part, sourced from the original manufacturer for use with small engines. The metal connecting rod is used to link the piston and the crankshaft and to convert the piston's lateral movement to a rotation of the crankshaft. This connecting rod is sold individually.

This is a genuine replacement part which is supplied directly from the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is one of the special screws utilized to secure the cylinder head, please make sure to refer to the appropriate diagrams of your model for the c...Read moreorrect application of this hardware. Keep in mind this is a high-quality item which is made of durable metal and is sold individually.