9027L Makita Grinder - Overview

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This cord is a genuine Makita replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Over time, power tool cords will wear out or become frayed. We recommend replacing a cord as soon as signs of wear are visible. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 8 Feet Long

This authentic replacement ball bearing which is supplied by the original manufacturer, it is specially designed for use with Makita power tools. Ball bearings are used to reduce friction between rotating parts, they experience constant wear from pressure, heat, vibration, and friction eventually requiring replacement to maintain peak per...Read moreformance. It is generally used as one of the armature bearings, for correct application make sure to check appropriate diagrams of your model. This part is made of high-quality metal and it is sold individually.

Set of 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes ...Read morecan fix a motor that's operating intermittently. • New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

This cord guard / strain reliever is a genuine Makita replacement part. It covers the final portion of cord before entering the tool, providing extra rigidness and preventing cord damage. Over time these cord guards break down and require replacement. The guard is constructed of heavy duty rubber compound for toughness. This cord guar...Read mored is compatible with the tools listed below. It is not guaranteed to fit any other power tool models.

This replacement hardware is a genuine OEM sourced part, it is not an aftermarket imitation. It is a commonly used with Makita power tools. This standard hardware has multiple applications depending on the tool. Please refer to appropriate diagrams for correct location and use of this screw. It is a pan head screw which is sold individual...Read morely. You will need a Phillips head screwdriver to install or remove this hardware.

This genuine OEM woodruff key is a small, semicircular metal piece used in various power tools to connect rotating parts, such as shafts or gears, to other components like wheels or pulleys. It prevents slippage between these parts, ensuring smooth synchronization and power transmission. With a width of 3/32 inches and a length of 5/8 inc...Read morehes, consider replacing a woodruff key if you notice misalignment or excessive movement between the connected parts. Be sure to inspect the key for signs of wear, damage, or bending. Removing the key depends on the make and model of your tool. If the key is visible, gently tap it from one side using a small hammer and a punch or drift pin. This will dislodge it from its slot. If the key is stuck or difficult to access, you may need to partially disassemble the tool to gain better access to the key. Once the key is loose, carefully pull it out using pliers. Clean the keyway and slot before installing the new key. Before making your purchase, remember that this component is sold individually.

This is a manufacturer sourced replacement part designed for use with Makita power tools. It helps to secure the brush in the housing. This screw-in cap is made of hard plastic and it is sold individually and measures 7-18 HM 1500. To replace it you would need a flat-head screwdriver.

This is an authentic Makita replacement part, sourced from the original manufacturer for use with power tools. The special retaining ring is commonly used to secure a part assembly to a shaft such as an armature and bearing. This retaining ring is available as an individual replacement part, please see model diagram for associative parts.