900-26 ((1695459)(2007)) Murray Snow Blower - Overview

This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lu...Read morebricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.

This is an authentic OEM sourced driver belt, not an aftermarket equivalent. It is specially designed for a variety of snow throwers. This is the main drive belt for the unit that will spin the augers. Please make sure to check appropriate diagrams for correct location and application of this item. It is made from durable rubber material ...Read moreand it is sold individually. You would need a set of wrenches to complete this repair.

It is an authentic OEM part which is specially designed for Murray, Snapper and Simplicity snowblowers. This bearing secures and stabilizes moving parts to ensure proper rotation angle and position. Unfortunately, over time the components will wear out and may begin to fail eventually requiring a replacement. Keep in mind this high-qualit...Read morey item is made of durable metal and is sold individually. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware.

This is an original part from Craftsman for use with Craftsman Snowblowers. The fiction wheel assembly meshes with the friction disc, causing the drive wheel axle to turn. The most common reason for replacing the friction wheel is when the snowblower's wheels don't turn.This part is sold individually. Disconnect the spark plug wire before...Read more installing this part. The tools that you will need to replace the friction wheel disc are 3/8" socket, 9/16" socket, adjustable wrench, hammer, 1/2" socket, flat-head screwdriver, and lubrication.

This is an original replacement part manufactured for use with Craftsman snow throwers. The special bolt is used to secure the auger blade to the axle. The bolt is used as a safeguard if the blade gets caught or stuck the force will snap the bolt rather than breaking more expensive parts like the auger transmission. The bolts are sold in ...Read morepairs and include the nuts and washers, the bolt sets are sold as individual sets.

This genuine item is supplied by the original equipment manufacturer for use with Murray, Simplicity and Snapper lawn mowers. It is the special retaining ring for the wheel. If the hardware is missing or is damaged, this will provide an identical replacement for the original part that was installed on a new unit. One durable metal retaini...Read moreng ring is included. Make sure to check the appropriate diagrams for your model to ensure the correct repair procedure.

This is available as an individual replacement part. The auger bearing connects to the auger plate and is made of plastic. If this part becomes broken it will need to be replaced and may require a screwdriver during the installation. It is an OEM Craftsman part directly sourced from the manufacturer for use in snowblowers.

This hex locknut has a special locking feature to prevent it from loosening due to vibrations or movement. It has a 1/4 inch diameter and a 20 threads-per-inch pitch. You will find it securing various parts of your lawn equipment, such as blade assemblies, engine mounts, or handles. A broken locknut cannot fasten components together tight...Read morely. Replace any damaged locknuts to keep your machine securely assembled and functioning properly. Loosen a locknut from your machine by turning it with a wrench or a socket. This durable metal locknut is an OEM hardware. It is sold individually, so read your user manual to determine how many you will need. Consider getting extras if you are replacing one, as these locknuts tend to wear out together.

This is a genuine manufacturer-sourced component which is specially designed for use with Murray and Simplicity snowthrowers. It provides an identical replacement for a missing or a faulty auger clutch spring that was installed on a new unit, please make sure to check the diagrams of your model for the correct location and application of ...Read morethis hardware. Keep in mind this durable part is made of high-quality metal and is sold individually.

This part is an OEM from Craftsman for use with Snow Blowers. The extension spring is used to provide tension between the link rods, and disconnect arm which slows the riding lawnmower down when the speed control is pushed. The most common reason for replacing the spring is if the drive belt does not have enough tension to engage the auge...Read morer pulley because the spring is broken. This part is sold individually. The tool that you will need to replace the extension spring is a socket wrench.

This is a genuine OEM sourced part is which is specially designed for use with Murray snowthrowers. The inner retainer ring helps to secure the chute collar and the lower chute. Over time it may wear out or get damaged eventually requiring a replacement. It is made of durable plastic and is sold individually. Note, the hardware to secure ...Read moreit is sold separately. Make sure to check the appropriate diagrams for your model to ensure the exact location and the correct application. A wrench set will be needed to perform this repair.

The shear pin spacer sleeve goes between the auger and the snowblower screw. This part is priced individually. This is an authentic Craftsman replacement part that is sourced from the original manufacturer for use with snowblowers. A wrench may be needed during the replacement of this item. It is made out of metal and will need to be replaced if it breaks.