This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on th...Read moree appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.
This is a door hinge, which allows for your washer door to properly shut during the washing cycle, and open after it is finished. If your door hinge is bent or broken and not allowing the door to shut properly, this hinge needs to be replaced immediately. Replacing this hinge will require a screwdriver to remove and install. This door hin...Read morege is an OEM part made of durable metal, and does not come with any other parts, like the necessary securing screws or install bracket.
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
This is a dryer door hinge cap, also known as a bushing, which is a durable plastic cap that is installed on the door hinge and is used to allow your dryer door to operate smoothly when opening and closing. If the door for your dryer is not properly opening and closing, this cap needs to be replaced immediately. To replace this door hinge...Read more bushing, you will need a screwdriver to remove and disassemble the door for your dryer. This door hinge bushing is sold individually, but normally wears at the same rate as the others within your dryer door, so order as many as are needed.
The leveling leg locking nut is an OEM replacement fastener for use in dryers and washers. It has a head diameter of 3/8 inches and a thread pitch of 16 threads per inch. The nut secures the leveling legs which helps to stabilize and level the appliances when they are placed on uneven surfaces. The nut ensures that the leg is stable and d...Read moreoes not move during operation. Over time, the threads on the nut may become stripped, or the nut can corrode and break rendering it unable to secure the leveling legs. A faulty nut will cause the appliance to shake and vibrate excessively, and potentially damage the floor and its internal components. It is recommended to replace both the leveling leg and nut at the same time. Use a wrench or pliers to loosen and remove the old locking nut from the leveling leg. Thread the new nut on to the leveling leg and ensure that it is tightened securely. Be careful not to overtighten and damage the threads. Gently shake the appliance to ensure that it is stable and level. Each nut is sold individually.
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to give a fresh new look to any handles or areas that have discoloring due to wear. Make sure to clean the area before you begin and wear a pr...Read moreotective mask for safety. Give the can a good shake and spray a few inches away from the surface. Apply the paint until the area is fully covered as desired. Wait until the paint has dried before using the appliance.
Note: This part has been updated by the manufacturer. It may appear different but will still function the same as the original. The hose clamp is about 2 inches in diameter and made of stainless steel. A hose clamp generally attaches hoses and tubes to various equipment This part consists of a band and a screw that tightens along the slot...Read mores when it is turned. This part works with washers, dishwashers, food waste disposers, and ice makers. This will need to be replaced if you notice leaking coming from the appliance.
This Affresh Washing Machine Cleaner deep cleans to help remove the odor-causing residues and grime that daily loads leave behind. The time-release tablets are EPA Safer Choice certified, septic-safe and designed to clean inside all machines, including HE (High Efficiency). Use monthly or every 30 cycles for a consistently clean machine.
This is an OEM boot seal retaining ring for various models of front-load washing machines. This retaining ring is used to clamp down and secure the inner boot, also known as a seal or gasket, of your washing machine. Over time and with extended use, this retaining ring may break or become worn out, and need replacing. This ring measures ...Read morefeatures a diameter of approximately 16.3 inches and is made of metal. Because this ring is highly compressed, you will need a set of pliers to secure it around the boot seal of your washing machine. This retaining ring is sold individually, so it does not come with any other parts.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
One of the hinges broke, making the door sag
21 of 30 peoplefound this instruction helpful.
Sandy from MILWAUKIE, OR
Easy
1- 2 hours
Using the Torx Screwdriver, we removed the door from the unit. Then we removed all of the screws on the inside of the washer door. After that we flipped it over and opened it up exposing the inside. We couldn't separate them entirely because there was a screw under the latch piece that we couldn't figure out how to get to. However with a
... Read morell the screws out on the inside of the door, we did have enough room to open it up and access the place cover that holds the hinges in. Once we accessed that we removed the roller tips from the old unit and placed them on the new one. Then we reversed the process. With a couple screws in we realized we had put the hinge in reversed from what it needed to be, so we reopened it and switched it around. Then completed replacing all the screws and reattached it to the washer. It opens and closes perfectly and we saved a couple hundred dollars for sure, as the quote to come out had been a $150 trip charge.
Read less
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 227 peoplefound this instruction helpful.
Michelle from Richardson, TX
Really Easy
Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
It took two of us to hold the ring and slide it on around the opening with the assistance of screwdrivers the spring was very tight
6 of 7 peoplefound this instruction helpful.
Terry from JUPITER, FL
A Bit Difficult
Less than 15 mins
Screw drivers
Two people to screwdrivers, stretching the spring out and around and that’s the last part to go on