This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
This ice cube tray is located inside your refrigerator and is eleven inches long, with 48 molds. It comes in white and is made entirely from plastic. If your tray is broken, cracked, or damaged, replacing this part can solve the problem. Here are some ice cube tray tips to consider: the easiest way to release the cubes is by giving the tr...Read moreay a twisting motion from both sides. If that does not work, set it on your counter for a couple minutes until the tray warms up and it should work. Remember not to beat the tray, especially on a hard surface, to prevent damage. Refer to manual instructions provided by the manufacturer if needed.
This white fresh food door gasket measures approximately 30-3/4 inches by 39 inches. It is used on many fresh food doors of top mount model refrigerators that have been manufactured since 1980.
This is an OEM part that is made of metal and sold individually. The leveling leg is generally used with refrigerators, dryers, freezers, ranges, cooktops, and microwaves. The leveling leg is meant to keep your appliance steady and level to the floor. If you notice your appliance is uneven to the floor it may need to have the leveling leg...Read more replaced. You will notice that the bottom of the leveling leg has a smooth surface to ensure moving your appliance does not require as much effort. This part screws into a pre-drilled hole underneath the appliance.
This rivet is an inch and a half long. It is used for many washing machines, microwaves, refrigerators, dryers, and ranges. Use of this rivet requires a rivet tool.
This bushing is used with a 1/4-inch pin. This part is found in refrigerators (and sometimes freezers). The bushing provides a bearing surface for the hinge pin that rotates. Every time you are opening and closing your fridge, this part is acting as a bearing and makes it so that the door is swinging back and forth with ease. This bushing...Read more tends to wear down over time and will need to be replaced. You will notice that this part needs to be replaced if your door is off-kilter and not aligned properly. This part is sold separately. This is a genuine part sourced from the manufacturer directly.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
cocktails running out of ice
56 of 61 peoplefound this instruction helpful.
Craig from Westminster, CA
Very Difficult
More than 2 hours
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
filled both ice cube trays up with water and placed in the freezer.. within hours my ice oproduction was doubled! no more warm cocktails : )
Was this helpful?
Thank you for voting!
Thermostat ceased to function. Fridge very cold.
33 of 47 peoplefound this instruction helpful.
Paul from Millboro, VA
A Bit Difficult
30 - 60 mins
Screw drivers, Wrench set
I removed control knobs and a couple of screws and forced the assembly down enough to remove the old thermostat, and insert the new one. Lucky me it was a identical replacement item. Job took about an hour.
Was this helpful?
Thank you for voting!
Gasket wouldn't seal all the way around
6 of 6 peoplefound this instruction helpful.
Thomas from Mobile, AL
A Bit Difficult
1- 2 hours
Nutdriver
Due to some deformity of the gasket, it didn't seal all the way around. The instructions suggested using a heat light to warm the gasket with the door open. That didn't work too well so I closed the door and used a heat gun lightly in the areas it didn't seal. That worked great to soften the gasket so the magnet in the gasket could pull
... Read moreit gasket tight to the refrigerator. I let it cool with the door closed and it now seals perfectly.