EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

867713151 Kenmore Heater - Overview

Diagrams for 867713151

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer Screw 818 X 1/2 – Part Number: WP3390631
$7.47
In Stock
Washer Screw 818 X 1/2
Part #WP3390631
This screw is sold individually.
Lower Dishrack – Part Number: 99002572
No Longer Available
Lower Dishrack
Part #99002572
UPDATE: As per Manufacturer - this rack is just the bare dishrack. Nothing included - must order wheels, fold-away tine latches and fold-away tine clips separately. These extra parts are NOT included with the rack.
Washer Screw – Part Number: WP273556
$7.47
In Stock
Washer Screw
Part #WP273556
Sold individually.
DISCONTINUED – Part Number: 902802
No Longer Available
DISCONTINUED
Part #902802
CLAMP – Part Number: 341029
$17.15
Special Order
CLAMP
Part #341029
Grommet – Part Number: 68987
No Longer Available
Grommet
Part #68987
DISCONTINUED – Part Number: 86023
No Longer Available
DISCONTINUED
Part #86023
SWITCH – Part Number: 45-1901
No Longer Available
SWITCH
Part #45-1901
EYEBOLT – Part Number: 75295
No Longer Available
EYEBOLT
Part #75295
EVAPORATOR SUPPOR – Part Number: 13-4556
No Longer Available
EVAPORATOR SUPPOR
Part #13-4556
SHELF SUPPORT – Part Number: 13-4551
No Longer Available
SHELF SUPPORT
Part #13-4551
SCREW – Part Number: 75493
No Longer Available
SCREW
Part #75493
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer wouldn’t drain and spin
3 of 3 people found this instruction helpful.
  • Thomas from KENT, CT
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I re moved actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.
Was this helpful?
Thank you for voting!
Replaced rusting lower dishwasher rack
  • Nancy from Springfield, VA
  • Easy
  • 15 - 30 mins
The only difficulty with installing the new lower dishrack was that the back tines came as 2 separate pieces with no instructions or clips. We ended up using white zip tipes to attach the pieces.
Was this helpful?
Thank you for voting!
Rusty lower dishrack
  • David from ANN ARBOR, MI
  • Easy
  • Less than 15 mins
Ordered lower dishrack PS2099930 (FSP 99002572). My old rack had permanent tines in 3 quadrants & foldaway tines in right rear. New rack (which came w/wheels) had permanent tines only in front 2 quadrants, plus 2 loose long tine rows (later ID'd as PS2099527, Front Fold-Away Tine, and PS2099528, Rear Fold-Away Tine). Ordered PS2097246 (Re ar Rack Bowl Tine Row) to replace my existing rusty tines, but "on order" really meant "not available anywhere." Watched installation video for PS2099037 (Fold Away Tine Clip) which clearly matches the loose tine rows that came with rack, but was problematic since my center spindle is permanently mounted on floor of cabinet, not on the rack. Fold-Away Tines could be cut off, but they would start rusting immediately. Ordered 4 PS343939 (Tine Row for upper dishrack) and 4 PS2099037 (FSP 99001436 Fold Away Tine Clip), hoping that these tine rows would clear the spindle. They work ok, but do graze the spindle slightly. Undecided whether I will tolerate the consequent floppiness of the tines, or permanently lock into place using nylon cable ties. Actual installation easy, with no extra tools, once I acquired parts that fit.
Was this helpful?
Thank you for voting!