This is replacement vent grille or vent grill for your microwave. You will find the grill vent either above or below the microwave door, depending on your model. If your vent grill is discolored or cracked, or if the mounting brackets for the grill are broken, you may need to replace the grill. This part is made of black plastic and is ap...Read moreproximately 24 inches long and 3.5 inches wide. This product is sold individually.
This is a light bulb and it is a part for your microwave. This bulb uses 30 watts, operates on 125 volts, and is an incandescent lamp. The function of this bulb is to illuminate the surface underneath and inside of your appliance while the door is open, and during a cooking cycle. You will need to replace this part if your door is open an...Read mored the light is not activated. We recommend that you unplug your microwave and leave it inactive for some time before making this repair. Proceed with caution as the capacitors in a microwave can hold dangerous electrical charges for long periods of time even when the appliance has been unplugged.
This bracket holds the metal or plastic flapper that closes off the exhaust duct when the fan is not running and opens when the fan turns on. If the exhaust fan on your microwave does not appear to be working, the problem may be with the damper assembly. If the damper does not open and close easily, check for any damage to the bracket, an...Read mored replace if it is damaged or faulty. This genuine OEM exhaust damper measures approximately 12 inches long by 5 inches wide.
This charcoal filter in manufactured to fit a microwave. It removes food odors from the air circulating through your appliance vent. Youi may need to replace this part if you notice odor when cooking your food or if your filter is clogged. It measures approximately 9.5 inches wide and 3 inches tall, and is black in color.
This stirrer fan cover is a genuine replacement part. This piece of plastic covers the stirrer fan and motor. It prevents dirt and grease from getting into the wave guide and damaging your appliance. Please note that you should not use your microwave without this part, it helps protect it from sparking.
This grease filter is a manufacturer-approved replacement part for your microwave. This filter is roughly 7.75 X 15 inches. The grease filter helps contain grease and food particles that result from heating food. It can become clogged over time and need replacing. This is an easy repair.
This magnetron in your microwave creates the radiation needed for cooking or warming your food. It is located inside the main cavity, typically near the transformer or waveguide. When the magnetron becomes defective, your food may not heat up properly or heat up at all. Additionally, buzzing or humming sounds may be noticeable while the m...Read moreicrowave is in operation. With a malfunctioning magnetron, your microwave loses its primary function. To remove it, you first need to unplug your microwave from its outlet. Before touching any components, discharge the capacitor by placing a screwdriver, with an insulated handle, across the two terminals of the capacitor. Once the capacitor is discharged, replace the current magnetron by disconnecting it from any wires and removing any mounting screws or clips. This magnetron is sold individually and is supplied directly from the original equipment manufacturer.
If the turntable on your microwave does not rotate, or you can hear a grinding noise, the problem may be with the motor. The motor is typically located below the floor of the oven, and is accessed through the bottom. The motor is normally held in place with a retaining screw and will have two wires attached to it as well. If the motor is ...Read moremaking a grinding noise it will need to be replaced. If the motor does not turn, you can check for voltage or continuity with a multi-meter. Make sure the power is disconnected from your microwave before beginning this repair.
Usually found kitchen appliances, this OEM-certified diode cable assembly helps to convert power from the transformer to the magnetron, to heat up your food. A damaged cable assembly will cause your appliance to heat food inconsistently or to not work at all. You might notice a burning smell or a loud buzzing sound coming from your applia...Read morence. If you do not replace a broken cable assembly, the components that produce heat in your appliance can overheat and fail. To replace your cable assembly, start by unplugging your appliance from any electrical source. Remove any protective casing from the assembly by unthreading any screws or clips. Disconnect the cable assembly from the transformer and the magnetron with pliers. Reinstalling a new cable assembly requires you to reverse the previous steps. Please keep in mind that this cable assembly is sold individually.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Vent Grille tabs snapped off
18 of 27 peoplefound this instruction helpful.
Andy from PERRYSBURG, OH
Really Easy
30 - 60 mins
Screw drivers
Repair was easy but you have to remove the screw at the top of the microwave (top left) in order to secure the far left tab with the hole in the tab. Place the grille in place, push to the left and then secure the screw you removed. Just remember that the mounted screw will need to be removed the next time you need access in order to repl
... Read moreace the charcoal filter.
Read less
Was this helpful?
Thank you for voting!
One of the switches in a component that door activates when shut.
9 of 11 peoplefound this instruction helpful.
Jimmy from OZARK, MO
Easy
30 - 60 mins
Pliers, Screw drivers
I replaced the whole component with all three switches in it even though only one switch was bad . Taking out one switch out of the holder unit would probably have damaged the unit that was holding the switches. Easy install and it works great again .
Was this helpful?
Thank you for voting!
would not start.
8 of 10 peoplefound this instruction helpful.
James from VIRGINIA BCH, VA
Really Easy
30 - 60 mins
Screw drivers
diagnosed defective 'door-shut switch' in the switch holder assembly. rather than replace switch, replaced entire locker holder assembly which made for a very simple and easy repair...not to mention very inexpensive.