8410BV Makita Hammer - Overview

This genuine OEM steel ball is found within the housing of your power tool. It serves as a detent mechanism, securing the shift knob in various positions to allow for the selection of different operating modes. It has a diameter of 4.8mm. If you notice signs of wear or deformation on the steel ball, it is a clear indication that it needs ...Read moreto be replaced. A worn-out steel ball can result in a loose shift knob that fails to hold its selected position properly. To locate and access the steel ball within the housing, refer to the instructions outlined in your user manual. Your tool may use steel balls of different sizes, so confirm that this is the correct part your repair will need before making your purchase.

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls re...Read moreduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This manufacturer sourced replacement pin is made out rubber and it is sold individually. It acts as a cushion/spacer in a variety of Makita power tools. This is a standard piece of hardware and it has multiple applications based on your tool. Please refer to diagrams for correct application.

This is a Ball Bearing that is sealed on both sides. This is a genuine Makita replacement part that is sold individually. • Ball bearings minimize friction between 2 parts in your tool that would otherwise spin and rub against each other. The balls or rollers take the load and spin, distributing the weight evenly while the minimal co...Read morentact area of the balls reduce friction. This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is an authentic OEM component from Makita. The compression spring 4 is compatible with a variety of power tools, and is sold individually. This metal spring provides the necessary tension for the tool motor, and is sold individually. For the the replacement, pliers and a screwdriver may be required.

It is an authentic OEM supplied item that is specially made for Makita screwdrivers and drills. This part helps to protect other components from dust, this part provides an identical replacement for a missing or damaged dust cover that was originally installed on a new unit. Please make sure to check the appropriate diagrams of your model...Read more for the correct location and application of this item. Keep in mind this high-quality item is made of durable plastic and is sold individually.

This 5 x 8 carbon brush holder is a genuine OEM replacement part used in various outdoor power equipment. It is a small plastic box with a cavity, and it is located near the engine assembly. The brush holder is responsible for holding and making electrical contact with the carbon brushes. The carbon brushes provide electrical current to t...Read morehe moving parts of the equipment. A faulty carbon brush holder will lead to reduced power output or complete loss of power. You will notice difficulties starting the engine, and the equipment may shut off during use. To begin the repair, first disconnect the power source. Remove the motor housing cover to access the holder and release the old brushes. Attach the new holder in place and reinsert the carbon brushes. Reassemble your equipment and switch it back on to check for functionality. Each brush holder is sold individually.

This is an authentic replacement part manufactured Makita power tools. The flat washer is commonly used to disperse pressure across a wider area on a part assembly that is applied by a nut or bolt. This flat washer is used with multiple types of power tools, please see model diagram for part location and usage. The flat washer is sold as an individual replacement part.

This is an authentic Makita replacement part. The flat washer is designed by the manufacturer for use in power tools such as chainsaws, rotary hammers, and coil nailers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different washers used in the mach...Read moreine. Refer to the parts diagram to be sure of ordering the correct part. You may require an Allen wrench or hex key when replacing this part. This item is sold individually.