Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 8241RS

8241RS Magic Chef Cooktop - Overview

Get Parts and Repair Help for 8241RS

If you know the cooktop repair part you need, you can browse the list of all parts on the 8241RS, or you can search by name or part description. You can also find your part by where it is located on the 8241RS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your cooktop. We’ve also included any installation videos we have for 8241RS parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$17.65

Top Burner Igniter

This is a surface burner igniter, also known as a top burner ignitor and stove top spark electrode. It is used to generate the spark that lights the surface burner. If your stove w...

Order within the next 5 hrs and your part ships today!
$2.96

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.

Order within the next 5 hrs and your part ships today!
$51.18

Burner Head Cap with Spark Electrode

The burner head cap with spark electrode directs the gas to the front and back burner heads and will equally distribute the gas across cooking areas. This part can help the followi...

Order within the next 5 hrs and your part ships today!
$3.02

Screw

This screw is sold individually.

Order within the next 5 hrs and your part ships today!
$2.96

Frame Screw

Sold Individually.

Order within the next 5 hrs and your part ships today!
$95.03

Spark Module

This part sends enough current to the igniter to create a spark to the bottom of the burner cap.

Order within the next 5 hrs and your part ships today!
$17.25

Top Burner Knob - black

This top burner knob is just over two inches in diameter. It is black in color and is made of plastic. This knob has white lettering denoting the off, low, light, and high position...

Order within the next 5 hrs and your part ships today!
$34.22

Burner Spark Ignition Switch

Order within the next 5 hrs and your part ships today!
$20.17

Burner Knob

Sold Individually. This knob accepts a D-shaped shaft.

Order within the next 5 hrs and your part ships today!
$2.96

Screw - 6-32 x 5/16

This screw is well under an inch long, and is made of metal.

Order within the next 5 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

gas burner ignitor failure

  • Customer: roy from East Providence, RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 125 of 139 people found this instruction helpful
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt ha... read more

top burners on stove won't ignite ,no clicking noise

  • Customer: scott from centreville, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 41 of 61 people found this instruction helpful
remove small panel on right side of stove,then un clip moduke and put wires from old module to new one.
Exact fit nomproblems. read more

Burner wouldn't start

  • Customer: Yury from Brooklyn, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 33 of 46 people found this instruction helpful
Make a quarter turn counterclockwise, disengage a burner head, disconnect 2 wires, connect to a new head, install turn clockwise.

That's it! read more