8228 - Overview

The OEM bearing, also known as the flange bearing, is silver, made of metal, and sold individually. It is used on riding mowers to secure the wheel in place and allow it to rotate freely on the shaft. Over time, the part may become worn and damaged, which you will notice if you experience a squealing or grinding sound from the wheel in qu...Read moreestion, or you notice the wheel is sloppy on the shaft. You will need a hammer and punch to complete this repair, which most of our customers rated as easy. Make sure you tap the new bearing into place evenly inside the tire rim.

The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle. This part is black, made of metal, and around an inch in length. It is sold individually and may become damaged over time due to wear and fatigue.

This OEM washer, also known as a flat washer, has dimensions of 25/32 x 1-1/4. Silver in color and metal, the washer is sold individually. Although this part can have a range of applications depending on the equipment, its general function is to spread the load under a bolt. Ensure you consult your owners manual or check your model number...Read more to confirm this is the washer you need for your equipment. This part will need to be replaced when your existing one is worn or damaged. It is an easy repair according to our customers, and does not require any special tools.

Genuine Husqvarna replacement part, this item is sold individually. This bearing is installed on top of the shaft which is encased in the mandrel assembly. The mandrel assembly is bolted to the mower deck. The shaft of the mandrel assembly is what the blade on all of the riding mowers listed below is attached to.

This is a genuine OEM part made for Craftsman lawn tractors and mowers. Bearings are used to buffer moving parts from damage due to friction. They also stabilize directional movement. Bearings are high-wear parts and are changed regularly. This metal bearing is sold individually. Gauges, washers, rings, etc. sold separately.

The Push Nut is a black, metal nut, which can be installed with pliers and a hammer. It's used to secure parts in place in various locations on a variety of equipment. If damaged will not longer hold in place. Installation is rated as "Easy", but it will depend on the parts your are securing and the equipment you are using. Consult your m...Read moreake, model and diagrams to ensure this is the correct part. The part is sold individually.

This is a genuine replacement belt sourced directly from the original manufacturer, designed for use with riding lawn tractors and mowers. Made from durable rubber and sold individually, this belt is responsible for driving the mower blades, making it a critical component for cutting performance. To ensure optimal function and longevity, ...Read moreit’s important to clean the pulleys before installing the new belt and to inspect the belt regularly for signs of wear or stretching. Replacing the belt requires a wrench set and pliers. For safety, always disconnect the spark plug wire before beginning. Start by lowering the mower deck to its lowest position and setting the blade engagement lever to the "Off" position. Roll the old belt off the engine pulley from between the belt guide and pulley. Remove the mower deck by taking out the bow-tie pins securing the left and right lift arms, then disconnect the blade engagement cable. Next, remove the bolts from the mower deck belt pulley covers and take off the covers. Loosen, but do not remove, the nuts on the top of the idler pulleys. Install the new mower deck belt through the belt guides and around the pulleys, then tighten the idler pulley nuts. Finally, reassemble the deck to complete the repair and restore your mower’s cutting performance. Lawn mower deck belt. Width: 1/2 " Length: 95 1/2 ".

This OEM-certified washer provides support, spacing, and reduces friction between parts in your lawn equipment, typically working alongside bolts or screws. This washer has a thickness of 16 gauge and dimensions of 25/32 x 1-5/8 inches. A damaged washer will look deformed or cracked, leading to parts becoming loose or not fitting properly...Read more in your machine. When you remove a broken washer from your machine, you will need pliers or a wrench to loosen the bolt or screw securing it. Once the fastener has been removed, you can pry the washer with a screwdriver. It is important to know that this washer is sold individually. Before adding this replacement part into your cart, check your instruction manual to determine the number of washers your machine needs.

This is a Genuine OEM replacement part used on Ride Mowers/Lawn Tractors. This is the Wheel that helps to support the Deck and allows it to move around easier. This Wheel is made out of Plastic and it is Sold Individually. Please note the Bolt and Nut used to secure this Wheel are Sold Separately. To replace this item you would need a Wrench.

This is an original part from Husqvarna. The hood latch is constructed of flexible plastic, and is made for use with many riding lawn mowers. This component is fastened onto the lower bagger chute, latching it to the upper chute. The hood latch is sold individually. A pair of pliers and a screwdriver may be helpful for the removal and replacement.

It is an authentic replacement cap-spindle that is supplied by the original equipment manufacturer for use with Poulan, Ryobi and Husqvarna riding lawn mowers and garden tractors. It is an identical replacement for a missing or damaged cap that was originally installed on a new equipment. The cap is utilized to cover the spindle. Make sur...Read moree to check the appropriate diagrams of your model for the exact location and application of this hardware. This high-quality cap-spindle is made of durable plastic material and is sold individually.

This is an authentic part that is supplied directly from the original equipment manufacturer for Craftsman lawn tractors. The blade bolt is used to secure the mulching blade. In order to replace the bolt, a socket wrench will be needed to remove the bolt from the mulching blade. This part is made of metal and is sold individually.

The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There are two ports for water to enter and this valve is compatible with a half-inch ID hose. It has two 3/4-11x1/2 NHT hose threads. You may hav...Read moree a faulty valve if your washer is leaking, has no hot or cold water, will not stop filling with water, will not fill with water, fills and drains at the same time, or is noisy. To confirm that the valve is faulty, unplug the washer when the symptom occurs. If the washer continues to fill, then the inlet valve is defective.