8188A89 (1998) Husqvarna Lawn Tractor - Overview

The OEM bearing, also known as the flange bearing, is silver, made of metal, and sold individually. It is used on riding mowers to secure the wheel in place and allow it to rotate freely on the shaft. Over time, the part may become worn and damaged, which you will notice if you experience a squealing or grinding sound from the wheel in qu...Read moreestion, or you notice the wheel is sloppy on the shaft. You will need a hammer and punch to complete this repair, which most of our customers rated as easy. Make sure you tap the new bearing into place evenly inside the tire rim.

The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle. This part is black, made of metal, and around an inch in length. It is sold individually and may become damaged over time due to wear and fatigue.

This OEM washer, also known as a flat washer, has dimensions of 25/32 x 1-1/4. Silver in color and metal, the washer is sold individually. Although this part can have a range of applications depending on the equipment, its general function is to spread the load under a bolt. Ensure you consult your owners manual or check your model number...Read more to confirm this is the washer you need for your equipment. This part will need to be replaced when your existing one is worn or damaged. It is an easy repair according to our customers, and does not require any special tools.

Genuine Husqvarna replacement part, this item is sold individually. This bearing is installed on top of the shaft which is encased in the mandrel assembly. The mandrel assembly is bolted to the mower deck. The shaft of the mandrel assembly is what the blade on all of the riding mowers listed below is attached to.

This is a genuine OEM replacement part used with many lawn tractor engines. The Craftsman screw (1/4-20 x 5/8) secures the cover to the riding mower deck housing. This hardened metal item is sold individually. Keep in mind three are needed for the repair, and a wrench is required for making the replacement.

An OEM part sourced directly from the manufacturer, this part is sold individually. Washers help to spread the load, and prevent damage to the surface being fixed, or provide some sort of insulation such as electrical. Washers can also be important for preventing galvanic corrosion. This specific washer is commonly used with outdoor law...Read moren equipment, and is compatible with the mowers and tractors that are listed below.

This is a genuine OEM part made for Craftsman lawn tractors and mowers. Bearings are used to buffer moving parts from damage due to friction. They also stabilize directional movement. Bearings are high-wear parts and are changed regularly. This metal bearing is sold individually. Gauges, washers, rings, etc. sold separately.

This item is sourced from the original manufacturer. It is an authentic part used with riding lawn tractors/mowers. This is the switch that allows user to engage blades. To stop mower blades, place attachment clutch control in the "DISENGAGED" position. One (1) plastic switch is included per order. Mechanical switches tend to break with t...Read moreime, eventually requiring replacement. This is standard 8 terminal black switch. Replacing this switch is a simple task. • Make sure to disconnect spark plug • Once you gained access under the housing disconnect wires • Remove old switch by pushing on side tabs • Secure new PTO switch • Reconnect wires and spark plug • Test the unit

This is a genuine replacement belt sourced directly from the original manufacturer, designed for use with riding lawn tractors and mowers. Made from durable rubber and sold individually, this belt is responsible for driving the mower blades, making it a critical component for cutting performance. To ensure optimal function and longevity, ...Read moreit’s important to clean the pulleys before installing the new belt and to inspect the belt regularly for signs of wear or stretching. Replacing the belt requires a wrench set and pliers. For safety, always disconnect the spark plug wire before beginning. Start by lowering the mower deck to its lowest position and setting the blade engagement lever to the "Off" position. Roll the old belt off the engine pulley from between the belt guide and pulley. Remove the mower deck by taking out the bow-tie pins securing the left and right lift arms, then disconnect the blade engagement cable. Next, remove the bolts from the mower deck belt pulley covers and take off the covers. Loosen, but do not remove, the nuts on the top of the idler pulleys. Install the new mower deck belt through the belt guides and around the pulleys, then tighten the idler pulley nuts. Finally, reassemble the deck to complete the repair and restore your mower’s cutting performance. Lawn mower deck belt. Width: 1/2 " Length: 95 1/2 ".

This OEM-certified washer provides support, spacing, and reduces friction between parts in your lawn equipment, typically working alongside bolts or screws. This washer has a thickness of 16 gauge and dimensions of 25/32 x 1-5/8 inches. A damaged washer will look deformed or cracked, leading to parts becoming loose or not fitting properly...Read more in your machine. When you remove a broken washer from your machine, you will need pliers or a wrench to loosen the bolt or screw securing it. Once the fastener has been removed, you can pry the washer with a screwdriver. It is important to know that this washer is sold individually. Before adding this replacement part into your cart, check your instruction manual to determine the number of washers your machine needs.

This is a Genuine OEM replacement part used on Ride Mowers/Lawn Tractors. This is the Wheel that helps to support the Deck and allows it to move around easier. This Wheel is made out of Plastic and it is Sold Individually. Please note the Bolt and Nut used to secure this Wheel are Sold Separately. To replace this item you would need a Wrench.

This genuine replacement mandrel stripper is sourced directly from the original manufacturer and is designed for use with riding lawn mowers and garden tractors. It functions as a mounting bracket between the mandrel assembly and the mower deck, while also serving to protect the mandrel housing and bearing from debris buildup. By preve...Read morenting grass and debris accumulation, this part helps extend the life of your mower’s mandrel components. Made from durable metal, this item is sold individually. Installation Tip: A wrench is required to complete the repair. Be sure to consult your model’s diagram to ensure proper fit and placement.