This is a single grease filter manufactured for a microwave. The microwave grease filter filters the exhaust air and traps any grease flowing out of the appliance. It is important to keep the filter clean and intact by cleaning it regularly and replacing it when needed. A clogged air filter can cause your appliance to run inefficiently an...Read mored possibly alter the taste and smell of your food. This filter is approximately 7.5 inches wide and 5 inches deep. This part is sold separately. No tools are required for this repair, the filter simply slides in and out using the easy-pull tab on the filter.
This is a light bulb and it is a part for your microwave. This bulb uses 30 watts, operates on 125 volts, and is an incandescent lamp. The function of this bulb is to illuminate the surface underneath and inside of your appliance while the door is open, and during a cooking cycle. You will need to replace this part if your door is open an...Read mored the light is not activated. We recommend that you unplug your microwave and leave it inactive for some time before making this repair. Proceed with caution as the capacitors in a microwave can hold dangerous electrical charges for long periods of time even when the appliance has been unplugged.
This bracket holds the metal or plastic flapper that closes off the exhaust duct when the fan is not running and opens when the fan turns on. If the exhaust fan on your microwave does not appear to be working, the problem may be with the damper assembly. If the damper does not open and close easily, check for any damage to the bracket, an...Read mored replace if it is damaged or faulty. This genuine OEM exhaust damper measures approximately 12 inches long by 5 inches wide.
Store the electrical energy needed by a microwaves high-voltage heating system with this replacement capacitor. During cooking, the capacitor works with the transformer, diode, and magnetron to help create the energy that heats food. A faulty capacitor may be linked to no heat, loud buzzing, or a fuse that blows when cooking begins. Howev...Read moreer, these signs can also come from other high-voltage components, so proper testing is important. Microwave capacitors may hold a deadly electrical charge even after the power cord is unplugged. For this reason, testing and installation must be completed by a qualified appliance service technician.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
One of the switches in a component that door activates when shut.
9 of 11 peoplefound this instruction helpful.
Jimmy from OZARK, MO
Easy
30 - 60 mins
Pliers, Screw drivers
I replaced the whole component with all three switches in it even though only one switch was bad . Taking out one switch out of the holder unit would probably have damaged the unit that was holding the switches. Easy install and it works great again .
Was this helpful?
Thank you for voting!
would not start.
8 of 10 peoplefound this instruction helpful.
James from VIRGINIA BCH, VA
Really Easy
30 - 60 mins
Screw drivers
diagnosed defective 'door-shut switch' in the switch holder assembly. rather than replace switch, replaced entire locker holder assembly which made for a very simple and easy repair...not to mention very inexpensive.
Was this helpful?
Thank you for voting!
Microwave not heating, everything else works
5 of 5 peoplefound this instruction helpful.
Barbara from Philadelphia, PA
Really Easy
15 - 30 mins
Screw drivers
Not knowing which of the switches to replace I ordered all three in the assembly. Replacing the full assembly was easy, first unplug the microwave. Then remove the top cover to access the screws that hold the control panel in place and let the control panel hang. There are two screws that hold the assembly in place - remove those. I u
... Read moresed needle nose pliers to pull the wires off of the switches and immediately put the wires on to the new assembly so there was no confusion on what wire went where. Place the assembly back in position, replace the two screws to hold it in, put control panel in place and secure screws. Replace top cover and plug in.