8101 - Overview

The Primer Pump, aka the Pump Bulb, is a clear, individually sold, plastic part, sourced from the original equipment manufacturer. It has an Outer Diameter of 0.616 Inches, 15.66mm and is 0.558 Inches and 14.19mm in height. This part is used to pump fuel from the tank to the carburator and is rated Easy to install. This part installs on...Read moreto the primer assembly. If the part dries out or starts leaking that means it is broken (likely due to fatigue or general wear) and must be replaced. Check the model number to ensure you are choosing the right part.

Also known as the Start Relay. The start relay briefly boosts the compressor, and then shuts off as soon as the motor gets up to speed.

This OEM Fuel Filter is a white and silver, steel part, sold individually. It requires a pair of pliers to install and is ranked as Easy to repair by our customers. This part attaches inside of the fuel tank, and is used to clean the fuel of debris. This part should be changed regularly as part of good engine maintenance. If the engine ...Read moresounds like it is not getting enough fuel or is underperforming, remove the filter to heck for a blockage. If there is a blockage or the part is leaking, then it likely needs a replacement.

This breather, also known as a fuel tank vent, is a genuine OEM replacement part used in trimmers and edgers. It is responsible for managing the pressure and air flow inside the fuel system, by acting as a valve for the fuel tank. It allows clean air to enter the tank, while preventing dirt and debris from entering as well. Over time, the...Read more breather can crack or become clogged leading to restricted air flow, inconsistent fuel supply, fuel leakage, hard starting, and engine stalling. Locate the breather on or near the fuel tank and disconnect the hoses and fasteners attached to it. Depending on your model you may need to remove the fuel tank to complete this replacement. Place the new breather in position and reattach the hoses and fasteners. Test the new part by gently blowing into the breather to confirm that the air flow is not restricted.

This fuel cap assembly is a genuine OEM part and is designed for use with outdoor handheld power equipment. Replacing your fuel cap is as simple as removing the old one and screwing the new cap on. This fuel cap keeps the fuel within the tank during operation, preventing leaks, and ensures that no dirt or debris enter the carburetor, filt...Read moreer, fuel lines or engine. Made of plastic with a cork seal underneath, this fuel cap is sold as an individual part, and has an approximately 2-inch diameter.

This individually sold fuel gasket is designed for use with handheld lawn and garden equipment and is the seal for the gas cap. This gasket is a genuine OEM part made of a composite material and will eventually become brittle because it interacts with gas and oil, meaning it will need replacing before it becomes debris in the fuel tank. T...Read morehis gasket not only prevents debris from entering the fuel tank, but it also prevents any leaks. To replace, simply unscrew your gas cap and remove the old gasket from the cap, and then replace it with the new.

The Recoil Starter Assembly, aka the Recoil Assembly, is a kit that includes the pulley, a return spring, the starter cord, and the pawls which engage the flywheel to turn over the engine. The components of this assembly are constructed of steel and plastic. The kit can be installed with a screwdriver and is rated as "Easy" to install...Read more (Tip: line all the parts up to install). This kit starts the engine, and you will know it is broken if the pull cord will not retract, or the engine is not engaging after it is pulled. The rope may also break. When the part breaks due to fatigue or general wear, it must be replaced. The part attaches on top of the engine where the flywheel is located.

This OEM Clip is a silver, steel part, which is sold individually. The part secures the fuel line to the fuel filter and is rated as Easy to install. You will know you need a new one if there is a leak around the hose where this clip is used to secure it, or if the fuel line detaches.

This air purge body assembly is a genuine OEM component. It is specially designed for Echo and Shindaiwa handheld lawn and garden equipment. By pressing on the purge bulb, it will force fuel into the fuel line from the fuel tank into the carburetor. Once the carburetor is full of fuel, the excess fuel will be purged back into the tank in ...Read morethe fuel return line. At some time the primer will lose its elasticity or crack and need to be replaced. It is a complete assembly which includes the plastic body housing and the rubber bulb. To ensure the correct installation of the new part, refer to the diagrams of your specific model. You will need a screwdriver to remove the old assembly and connect the new one.

This genuine Primer Cover, or Primer Pump Cover, is a silver, individually sold, steel part with dimensions of around 1x1 inch. This part is installed using a screwdriver, and is rated as Easy to install by our customers. This part secures the plastic primer bulb to the air purge body assembly, and must be replaced if damaged or bent.

This is a genuine manufacturer sourced replacement washer that is designed for use with Shindaiwa and Echo handheld lawn and garden equipment. It helps to distribute the pressure evenly between two connected parts, for proper application please make sure to check appropriate diagrams of your unit. This part is made from durable metal and it is sold individually.