EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

79691563910 Kenmore Dryer - Overview

Diagrams for 79691563910

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer Lint Filter – Part Number: ADQ56656401
$36.85
In Stock
Dryer Lint Filter
★★★★★
★★★★★
(178)
Part #ADQ56656401
This dryer lint filter assembly captures lint, hair, and loose fabric fibres as air leaves the drum. Its fine mesh screen allows air to pass through while collecting debris for easy removal after each load. A torn screen, cracked frame, or warped edge may let lint bypass the filter or prevent it from seating properly. Replacing a damaged assembly restores the screening surface and secure support. Cleaning collected lint after every load helps maintain airflow and supports normal drying times during everyday use. This is an OEM part sourced directly from the manufacturer.
4 PACK ROLLER ASSEMBLY – Part Number: 4581EL2002L
$144.76
In Stock
4 PACK ROLLER ASSEMBLY
★★★★★
★★★★★
(82)
Part #4581EL2002L
This part is sold individually. The drum support roller is found in your dryer. It is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. It is recommended that you replace both rollers at once. You may notice that this part needs to be replaced if you are experiencing a squeaking noise, which could be due to the bearing going bad. The bearing could be severely damaged if you hear a very loud thumping noise, much like you would when you are drying a pair of shoes.
Thermal Fuse – Part Number: 6931EL3003D
$19.75
In Stock
Thermal Fuse
★★★★★
★★★★★
(28)
Part #6931EL3003D
This thermal fuse acts as a high-limit thermostat, and shuts off the heating element when the dryer overheats by cutting off power to the dryer. If the thermal fuse has blown, the dryer will not start. These fuses cannot be reset, so if yours has blown, you will need to replace it. A common reason for the thermal fuse to blow on a dryer is if the exhaust vent on your dryer is restricted or blocked. Hot air will be confined in the dryer and the fuse will trip and stop the electricity from flowing to the gas valve or heating element.
Lint Screen Housing – Part Number: MCK49049101
$48.35
In Stock
Lint Screen Housing
★★★★★
★★★★★
(23)
Part #MCK49049101
Clothing stays separated from the lint duct opening with help from this gray plastic dryer lint filter cover and guide. It supports the removable lint screen and provides a smooth barrier around the filter area as laundry tumbles. Cracks, broken edges, or warping may cause garments to snag or prevent the screen from seating securely. Replacing a damaged cover helps restore filter support and protects the opening around the lint duct. The guide also supports routine removal and insertion of the screen for cleaning. This is an OEM part sourced directly from the manufacturer.
Moisture Sensor – Part Number: 6500EL3001A
$21.95
In Stock
Moisture Sensor
★★★★★
★★★★★
(6)
Part #6500EL3001A
Damp clothing makes contact with this dryer moisture sensor bar as it tumbles, providing an electrical signal used to monitor drying progress. The metal electrode works with the control system to adjust automatic cycle time as the load becomes drier. A damaged bar or poor electrical contact may cause the cycle to end too soon or leave clothes damp. Replacing a faulty sensor bar helps restore moisture detection, allowing the dryer controls to respond to the load and finish at the selected dryness level. This is an OEM part sourced directly from the manufacturer.
Dryer Drum Belt – Part Number: 4400EL2001F
$37.35
In Stock
Dryer Drum Belt
★★★★★
★★★★★
(8)
Part #4400EL2001F
Get clothes tumbling again with this dryer drum drive belt. It wraps around the drum and runs over the motor and tension pulleys, transferring motor power to turn the drum during drying. A cracked, stretched, or broken belt may slip, make unusual noises, or leave the drum still while the motor runs. Replacing a worn belt helps restore steady tumbling so clothes move through the warm air. Unplug the dryer before opening the cabinet, and follow the installation directions for proper belt routing. This is an OEM part sourced directly from the manufacturer.
Blower Thermostat – Part Number: 6931EL3002M
$53.85
In Stock
Blower Thermostat
★★★★★
★★★★★
(8)
Part #6931EL3002M
Monitor exhaust air temperature with this dryer blower housing thermostat. Mounted on the blower assembly, it responds to heat and opens its electrical circuit when the temperature reaches its set limit, helping protect the dryer from overheating. A failed thermostat may interrupt operation, leaving the dryer unable to start or heat properly. Replacing a faulty thermostat helps restore the temperature safety circuit. Unplug the dryer before opening the cabinet, and clear lint from the exhaust path to support proper airflow. This is an OEM part sourced directly from the manufacturer.
High Limit Thermostat and Thermistor Kit – Part Number: AGM30045804
$103.35
In Stock
High Limit Thermostat and Thermistor Kit
★★★★★
★★★★★
(14)
Part #AGM30045804
This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes too long to dry, then the thermistor might be defective or damaged. This can cause a fault code and could begin either prolonging or shortening drying time. As a safety precaution, make sure to unplug the dryer from the power source before beginning this installation, and wear gloves to protect your hands. Refer to the installation instructions provided by the manufacturer for further guidance.
Filter Guide – Part Number: MEA49050001
$33.83
In Stock
Filter Guide
★★★★★
★★★★★
(7)
Part #MEA49050001
A securely seated lint screen depends on an intact guide inside the dryer filter opening. This plastic lint filter frame supports the removable screen and guides it into place during insertion. Cracks, warping, or broken edges may leave the filter loose, prevent it from seating fully, or make removal difficult. Replacing a damaged guide helps restore proper filter support and limits gaps that allow lint to pass around the screen. The frame also keeps the filter aligned for routine removal and cleaning. This is an OEM part sourced directly from the manufacturer.
Dryer Thermostat Assembly – Part Number: 6931EL3001F
$58.25
In Stock
Dryer Thermostat Assembly
★★★★★
★★★★★
(2)
Part #6931EL3001F
Temperature protection in the dryer heating system depends on this rear high-limit thermostat assembly. It senses heat at its mounting location and opens the heating circuit when the temperature reaches its cutoff point, helping prevent excessive heat from damaging surrounding components. A faulty thermostat may interrupt heating, leave clothes damp, or prevent normal temperature control. Replacing a failed assembly helps restore the protective switching function needed during drying. The thermostat works within the heating circuit to limit heat when operating temperatures rise too high. This is an OEM part sourced directly from the manufacturer.
Felt Seal – Part Number: 4036EL3001A
$52.75
In Stock
Felt Seal
★★★★★
★★★★★
(4)
Part #4036EL3001A
Warm air stays within the intended drying path with help from this dryer drum felt seal. It closes the gap between the rotating drum and stationary housing while providing a cushioned contact surface as the drum turns. A worn, torn, or displaced seal may allow air and lint to escape into the cabinet or cause scraping noises during operation. Replacing a damaged seal helps restore proper airflow through the drum and reduces rubbing at the sealed edge, supporting smoother rotation and normal drying performance. This is an OEM part sourced directly from the manufacturer.
Filter Cover – Part Number: MCK66787901
$48.35
In Stock
Filter Cover
Part #MCK66787901
This dryer lint filter screen cover helps keep clothing and small items from slipping into the exhaust duct near the lint filter. The plastic flap fits into the filter housing and covers the opening when the lint screen is removed. Cracks, warping, or broken mounting tabs may keep the cover from sitting properly or moving as it should. Replacing a damaged or missing cover restores this protective barrier and helps prevent clothing from catching on broken edges around the lint filter area. This is an OEM part sourced directly from the manufacturer.

Common Symptoms of the 79691563910

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer making a thumping and squealing noise when running
132 of 171 people found this instruction helpful.
  • Mark from WAVERLY, OH
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable), Wrench set
Had to replace front drum support rollers. Removed screws underneath top in back that held bracket that keeps top in place. Slid top towards rear and lifted up. Removed 4 screws that hold plastic front panel in place (inside..2 on each corner) Unplugged front panel electric plugs to remove panel. Opened door..removed 2 screws at bottom of door opening. Removed screws on top of front panel. Unplugged door switch plug. Removed front panel. Removed right front roller with 9/16th wrench for nut. Adjustable for back of stud. Lifted up on drum to get roller out. Reversed to install. Left roller a bit harder to get to stud. Removed and installed same as right side. Did not attempt to replace rear rollers. Have them if needed but very much more involved to replace.
Was this helpful?
Thank you for voting!
Dryer would run with no heat
98 of 116 people found this instruction helpful.
  • Richard from ORMOND BEACH, FL
  • Easy
  • 30 - 60 mins
  • Screw drivers
I actually went to mr fix it on u tube. Great instruction on how to take dryer apart. First I unplugged the dryer. I found I could reach the heating system by removing the lint tube in the back of the dryer. I put my I phone with the light on inside the back of the dryer and tested the connections to see if all were working. The thermal f use was not working. I removed the two wires , red on top and white on the bottom. Then used a small Phillips screwdriver to remove the two mounting screws and removed the fuse. I then used a vacuum to clear any lint from the back of the dryer and inside the dryer. This took me about an hour and a half. I did it this way because I did not want to disassemble the entire dryer to get to the components. I received the fuse in 3 days and tested it. It was fine. I then put it in the dryer screwed it in place, connected the wires. Replaced the lint tube. This took about 10 minutes. Dryer is running great.
Was this helpful?
Thank you for voting!
Screeching during operation
66 of 101 people found this instruction helpful.
  • CAROL from NAMPA, ID
  • Really Easy
  • More than 2 hours
  • Pliers, Screw drivers
Found disassembly video and watched several times. Suspected that one of the drum wheels had seized up. Found extreme volume of lint and hair inside unit as well as a dryer sheet melted on top of heating unit. Front left drum wheel was worn down from lint and hair jamming its movement. Video made it easy, not a really complicated piec e of machinery. Replaced all 4 wheels due to normal wear on other three. Wanted to be sure drum evenly balanced on all 4. Parts came quickly and were easy to install. My sister and I did this together. Would not recommend doing it alone. Took time to vac and wipe down entire unit. Now it runs so quiet we have to look to see if it is operating. Got a brand new machine out of it, saved a couple of hundred dollars in repair bills, and found 11 cents inside the machine. For your own piece of mind, if you have had your dryer for several years, you need to open it up and clean it out. Its not hard... added note, we are both in our 60's... so if we can do it so can you.... Such a feeling of accomplishment, can't buy that in a store....
Was this helpful?
Thank you for voting!