EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

79691072310 Kenmore Dryer - Overview

Diagrams for 79691072310

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
4 PACK ROLLER ASSEMBLY – Part Number: 4581EL2002L
$144.76
In Stock
4 PACK ROLLER ASSEMBLY
★★★★★
★★★★★
(82)
Part #4581EL2002L
This part is sold individually. The drum support roller is found in your dryer. It is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. It is recommended that you replace both rollers at once. You may notice that this part needs to be replaced if you are experiencing a squeaking noise, which could be due to the bearing going bad. The bearing could be severely damaged if you hear a very loud thumping noise, much like you would when you are drying a pair of shoes.
Blower Thermostat – Part Number: 6931EL3002M
$53.85
In Stock
Blower Thermostat
★★★★★
★★★★★
(8)
Part #6931EL3002M
Monitor exhaust air temperature with this dryer blower housing thermostat. Mounted on the blower assembly, it responds to heat and opens its electrical circuit when the temperature reaches its set limit, helping protect the dryer from overheating. A failed thermostat may interrupt operation, leaving the dryer unable to start or heat properly. Replacing a faulty thermostat helps restore the temperature safety circuit. Unplug the dryer before opening the cabinet, and clear lint from the exhaust path to support proper airflow. This is an OEM part sourced directly from the manufacturer.
High Limit Thermostat and Thermistor Kit – Part Number: AGM30045804
$103.35
In Stock
High Limit Thermostat and Thermistor Kit
★★★★★
★★★★★
(14)
Part #AGM30045804
This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes too long to dry, then the thermistor might be defective or damaged. This can cause a fault code and could begin either prolonging or shortening drying time. As a safety precaution, make sure to unplug the dryer from the power source before beginning this installation, and wear gloves to protect your hands. Refer to the installation instructions provided by the manufacturer for further guidance.
Lint Filter – Part Number: ADQ73373201
$77.22
In Stock
Lint Filter
★★★★★
★★★★★
(27)
Part #ADQ73373201
Trap loose fibres and lint with this dryer lint screen filter assembly. Its fine mesh catches debris from the air leaving the drum, while the plastic frame holds the screen securely in place. Torn mesh, a cracked frame, or warping may let lint pass through or keep the filter from seating properly. Replacing a damaged filter helps restore lint collection and proper fit. Remove lint after every load to maintain airflow, and gently wash away residue when needed, allowing the filter to dry fully before reinstalling it. This is an OEM part sourced directly from the manufacturer.
Gas Igniter – Part Number: 5318EL3001A
$134.43
In Stock
Gas Igniter
★★★★★
★★★★★
(3)
Part #5318EL3001A
Gas burner ignition begins when this dryer igniter heats to a glowing temperature, allowing the burner to light and produce drying heat. The assembly includes a mounting bracket and wire harness for connection to the ignition circuit. A cracked or burned out igniter may prevent a flame from forming, leaving the drum tumbling without heat and clothes damp. Replacing a faulty assembly helps restore burner ignition and normal heating. The fragile heating surface requires careful handling to avoid damage during installation. This is an OEM part sourced directly from the manufacturer.
Safety Switch Assembly – Part Number: EBF61496102
$52.75
In Stock
Pulley Idle – Part Number: 4560EL3001A
$30.53
In Stock
Pulley Idle
★★★★★
★★★★★
(5)
Part #4560EL3001A
The drive belt moves smoothly around this dryer idler pulley wheel as the motor turns the drum. Working within the belt tensioning mechanism, the pulley guides the belt and helps maintain steady contact with the drive system. A worn, cracked, or seized wheel may cause squealing, grinding, belt slippage, or interrupted tumbling. Replacing a damaged pulley helps restore free belt movement and reliable drum rotation. Its rotating surface supports the belt during operation, reducing the friction that can lead to noise and premature belt wear. This is an OEM part sourced directly from the manufacturer.
Clamp – Part Number: 4861FR3068A
$16.45
In Stock
Clamp
Part #4861FR3068A
A secure hose connection helps keep water contained inside the appliance. This hose clamp applies pressure around the hose end, holding it firmly against its fitting during operation. A weakened, bent, or broken clamp may allow the connection to loosen and leak into the cabinet or onto the floor. Replacing a damaged clamp helps restore the grip needed to keep the hose attached and sealed. It secures the connection while allowing the hose to be removed when maintenance or replacement is required. This is an OEM part sourced directly from the manufacturer.
Conversion Kit - NG - LP – Part Number: 383EEL3002A
$34.05
In Stock
Conversion Kit - NG - LP
★★★★★
★★★★★
(5)
Part #383EEL3002A
This part converts a compatible gas dryer from natural gas to liquid propane operation. The conversion kit provides an LP burner orifice that meters propane at the rate required by the burner system. It is used when the fuel supply changes, rather than to repair a general heating problem. Correct conversion supports proper combustion and normal drying heat. Installation must follow the supplied conversion instructions, including the specified gas valve regulator adjustment, so the burner operates with the intended fuel flow and pressure. This is an OEM part sourced directly from the manufacturer.
Motor Pulley Assembly – Part Number: 4561EL3002A
$69.25
In Stock
Motor Pulley Assembly
★★★★★
★★★★★
(1)
Part #4561EL3002A
Proper belt tension keeps the dryer drum turning steadily during a cycle. This idler pulley assembly guides the drive belt and maintains tension as the motor rotates the drum. A worn, damaged, or seized pulley may cause squealing, allow the belt to slip, or prevent the drum from tumbling. Replacing a faulty assembly helps restore smooth belt movement and reliable drum rotation. The pulley turns continuously against the belt during operation, making a freely rotating wheel important for reducing friction and belt wear. This is an OEM part sourced directly from the manufacturer.
Locker Assembly – Part Number: 4027EL1001B
$35.33
In Stock
Locker Assembly
Part #4027EL1001B

Questions And Answers for 79691072310

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John - For model number 79691072310
April 1, 2023
Do you have a lint screen that fits this model?
Chris Boyle Profile
Hi John, thank you for the question. According to our research, the part you are looking for is the lint filter, part number PS7787727. We hope this helps!
$77.22
In Stock
Lint Filter
1 person found this instruction helpful.
Was this helpful?
Thank you for voting!
Billy - For model number 79691072310
March 20, 2025
Change from LPgas to natural gas
Chris Boyle Profile
Hello Billy, thank you for reaching out. To convert your dryer to the natural gas, you may need to install the natural gas orifice, part number PS3524507. Glad to be of assistance!
Was this helpful?
Thank you for voting!
Richard - For model number 79691072310
August 9, 2025
Need a LP kit from natural gas to LP gas
Chris Boyle Profile
Hi Richard, thank you for reaching out. The conversion kit for your model is part number PS3522299. We hope this information is useful!
$34.05
In Stock
Conversion Kit - NG - LP
Was this helpful?
Thank you for voting!
  • 1

Common Symptoms of the 79691072310

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer making a thumping and squealing noise when running
132 of 171 people found this instruction helpful.
  • Mark from WAVERLY, OH
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable), Wrench set
Had to replace front drum support rollers. Removed screws underneath top in back that held bracket that keeps top in place. Slid top towards rear and lifted up. Removed 4 screws that hold plastic front panel in place (inside..2 on each corner) Unplugged front panel electric plugs to remove panel. Opened door..removed 2 screws at bottom of door opening. Removed screws on top of front panel. Unplugged door switch plug. Removed front panel. Removed right front roller with 9/16th wrench for nut. Adjustable for back of stud. Lifted up on drum to get roller out. Reversed to install. Left roller a bit harder to get to stud. Removed and installed same as right side. Did not attempt to replace rear rollers. Have them if needed but very much more involved to replace.
Was this helpful?
Thank you for voting!
Screeching during operation
66 of 101 people found this instruction helpful.
  • CAROL from NAMPA, ID
  • Really Easy
  • More than 2 hours
  • Pliers, Screw drivers
Found disassembly video and watched several times. Suspected that one of the drum wheels had seized up. Found extreme volume of lint and hair inside unit as well as a dryer sheet melted on top of heating unit. Front left drum wheel was worn down from lint and hair jamming its movement. Video made it easy, not a really complicated piec e of machinery. Replaced all 4 wheels due to normal wear on other three. Wanted to be sure drum evenly balanced on all 4. Parts came quickly and were easy to install. My sister and I did this together. Would not recommend doing it alone. Took time to vac and wipe down entire unit. Now it runs so quiet we have to look to see if it is operating. Got a brand new machine out of it, saved a couple of hundred dollars in repair bills, and found 11 cents inside the machine. For your own piece of mind, if you have had your dryer for several years, you need to open it up and clean it out. Its not hard... added note, we are both in our 60's... so if we can do it so can you.... Such a feeling of accomplishment, can't buy that in a store....
Was this helpful?
Thank you for voting!
Gas Dryer not getting hot
28 of 45 people found this instruction helpful.
  • Terry from Goose Creek, SC
  • Easy
  • 30 - 60 mins
  • Screw drivers
I noticed the flame would start, then quit after about 15 seconds. I checked the flame detector, and found the lenze cracked. I replaced it, and it's as good as gold.

It looked like a hard job to take the drum out to get at the part. But the top was off with 3 screws, the front about 6 I think. Then the front frame, only 4 s crews. I think setting the belt tentioner was the hardest thing to do.

Done in 45 minutes, both the job, then the next load of laundry.
Was this helpful?
Thank you for voting!