This part is sold individually. The drum support roller is found in your dryer. It is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. It is recommended that you replace both rollers at once. You may notice that this part needs to be replaced if you are experiencing a squeaking noise, whi...Read morech could be due to the bearing going bad. The bearing could be severely damaged if you hear a very loud thumping noise, much like you would when you are drying a pair of shoes.
This lint filter fits select clothes dryers. It catches lint, dust, and clothing fibers before they enter the dryers air system. A clean filter helps maintain good airflow and drying performance. Replace it if the screen is torn, cracked, bent, or has holes. Clean the filter after every load and remove any buildup with a soft brush when n...Read moreeeded. Use the complete dryer model number to guarantee the proper fit. No tools are normally needed because the filter slides into the opening near the dryer door. This is an OEM part sourced directly from the manufacturer.
Damp clothing makes contact with this dryer moisture sensor bar as it tumbles, providing an electrical signal used to monitor drying progress. The metal electrode works with the control system to adjust automatic cycle time as the load becomes drier. A damaged bar or poor electrical contact may cause the cycle to end too soon or leave clo...Read morethes damp. Replacing a faulty sensor bar helps restore moisture detection, allowing the dryer controls to respond to the load and finish at the selected dryness level. This is an OEM part sourced directly from the manufacturer.
Get clothes tumbling again with this dryer drum drive belt. It wraps around the drum and runs over the motor and tension pulleys, transferring motor power to turn the drum during drying. A cracked, stretched, or broken belt may slip, make unusual noises, or leave the drum still while the motor runs. Replacing a worn belt helps restore ste...Read moready tumbling so clothes move through the warm air. Unplug the dryer before opening the cabinet, and follow the installation directions for proper belt routing. This is an OEM part sourced directly from the manufacturer.
Monitor exhaust air temperature with this dryer blower housing thermostat. Mounted on the blower assembly, it responds to heat and opens its electrical circuit when the temperature reaches its set limit, helping protect the dryer from overheating. A failed thermostat may interrupt operation, leaving the dryer unable to start or heat prope...Read morerly. Replacing a faulty thermostat helps restore the temperature safety circuit. Unplug the dryer before opening the cabinet, and clear lint from the exhaust path to support proper airflow. This is an OEM part sourced directly from the manufacturer.
This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes too long to dry, then the thermistor might be defective or damaged. This can cause a fault code and could begin either prolonging or shorte...Read morening drying time. As a safety precaution, make sure to unplug the dryer from the power source before beginning this installation, and wear gloves to protect your hands. Refer to the installation instructions provided by the manufacturer for further guidance.
Gas burner ignition begins when this dryer igniter heats to a glowing temperature, allowing the burner to light and produce drying heat. The assembly includes a mounting bracket and wire harness for connection to the ignition circuit. A cracked or burned out igniter may prevent a flame from forming, leaving the drum tumbling without heat ...Read moreand clothes damp. Replacing a faulty assembly helps restore burner ignition and normal heating. The fragile heating surface requires careful handling to avoid damage during installation. This is an OEM part sourced directly from the manufacturer.
Warm air stays within the intended drying path with help from this dryer drum felt seal. It closes the gap between the rotating drum and stationary housing while providing a cushioned contact surface as the drum turns. A worn, torn, or displaced seal may allow air and lint to escape into the cabinet or cause scraping noises during operati...Read moreon. Replacing a damaged seal helps restore proper airflow through the drum and reduces rubbing at the sealed edge, supporting smoother rotation and normal drying performance. This is an OEM part sourced directly from the manufacturer.
The drive belt moves smoothly around this dryer idler pulley wheel as the motor turns the drum. Working within the belt tensioning mechanism, the pulley guides the belt and helps maintain steady contact with the drive system. A worn, cracked, or seized wheel may cause squealing, grinding, belt slippage, or interrupted tumbling. Replacing ...Read morea damaged pulley helps restore free belt movement and reliable drum rotation. Its rotating surface supports the belt during operation, reducing the friction that can lead to noise and premature belt wear. This is an OEM part sourced directly from the manufacturer.
A firmly closed dryer door depends on a catch that grips the door strike securely. This dryer door latch assembly holds the door shut during tumbling while allowing it to release when pulled open. Worn gripping surfaces, cracks, or broken components may prevent the door from latching or allow it to pop open during a cycle. Replacing a dam...Read moreaged catch helps restore reliable closure and keeps the door seated against the front opening, reducing interruptions caused by the door coming loose during operation. This is an OEM part sourced directly from the manufacturer.
A secure hose connection helps keep water contained inside the appliance. This hose clamp applies pressure around the hose end, holding it firmly against its fitting during operation. A weakened, bent, or broken clamp may allow the connection to loosen and leak into the cabinet or onto the floor. Replacing a damaged clamp helps restore th...Read moree grip needed to keep the hose attached and sealed. It secures the connection while allowing the hose to be removed when maintenance or replacement is required. This is an OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer making a thumping and squealing noise when running
132 of 171 peoplefound this instruction helpful.
Mark from WAVERLY, OH
Easy
30 - 60 mins
Screw drivers, Wrench (Adjustable), Wrench set
Had to replace front drum support rollers. Removed screws underneath top in back that held bracket that keeps top in place. Slid top towards rear and lifted up. Removed 4 screws that hold plastic front panel in place (inside..2 on each corner) Unplugged front panel electric plugs to remove panel. Opened door..removed 2 screws at bottom of
... Read more door opening. Removed screws on top of front panel. Unplugged door switch plug. Removed front panel. Removed right front roller with 9/16th wrench for nut. Adjustable for back of stud. Lifted up on drum to get roller out. Reversed to install. Left roller a bit harder to get to stud. Removed and installed same as right side. Did not attempt to replace rear rollers. Have them if needed but very much more involved to replace.
Read less
Was this helpful?
Thank you for voting!
Screeching during operation
66 of 101 peoplefound this instruction helpful.
CAROL from NAMPA, ID
Really Easy
More than 2 hours
Pliers, Screw drivers
Found disassembly video and watched several times. Suspected that one of the drum wheels had seized up. Found extreme volume of lint and hair inside unit as well as a dryer sheet melted on top of heating unit. Front left drum wheel was worn down from lint and hair jamming its movement. Video made it easy, not a really complicated piec
... Read moree of machinery. Replaced all 4 wheels due to normal wear on other three. Wanted to be sure drum evenly balanced on all 4. Parts came quickly and were easy to install. My sister and I did this together. Would not recommend doing it alone. Took time to vac and wipe down entire unit. Now it runs so quiet we have to look to see if it is operating. Got a brand new machine out of it, saved a couple of hundred dollars in repair bills, and found 11 cents inside the machine. For your own piece of mind, if you have had your dryer for several years, you need to open it up and clean it out. Its not hard... added note, we are both in our 60's... so if we can do it so can you.... Such a feeling of accomplishment, can't buy that in a store....
Read less
Was this helpful?
Thank you for voting!
Gas Dryer not getting hot
28 of 45 peoplefound this instruction helpful.
Terry from Goose Creek, SC
Easy
30 - 60 mins
Screw drivers
I noticed the flame would start, then quit after about 15 seconds. I checked the flame detector, and found the lenze cracked. I replaced it, and it's as good as gold.
It looked like a hard job to take the drum out to get at the part. But the top was off with 3 screws, the front about 6 I think. Then the front frame, only 4 s
... Read morecrews. I think setting the belt tentioner was the hardest thing to do.
Done in 45 minutes, both the job, then the next load of laundry.