EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

79641373211 Kenmore Washer - Overview

Diagrams for 79641373211

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water Inlet Valve - Hot – Part Number: 5220FR2006H
$37.35
In Stock
Water Inlet Valve - Hot
★★★★★
★★★★★
(94)
Part #5220FR2006H
Hot water enters the washer through this single solenoid inlet valve, which opens when the control calls for hot water and closes when filling stops. It connects the household hot water supply to the internal fill system, regulating flow during selected wash cycles. A faulty valve may prevent hot water from entering, cause slow filling, or allow water to seep into the tub while the washer is off. Replacing a damaged valve helps restore controlled filling and proper shutoff of the hot water supply. This is an OEM part sourced directly from the manufacturer.
Rear Tub Gasket – Part Number: 4036ER2004A
$36.25
In Stock
Rear Tub Gasket
★★★★★
★★★★★
(15)
Part #4036ER2004A
Protecting the tub bearings from wash water, this rear tub shaft seal forms a barrier around the rotating drum shaft. The rubber seal fits into the rear outer tub and helps keep water and detergent away from the bearing area while the drum turns. A worn, torn, or hardened seal may allow leaks near the rear of the tub and expose the bearings to moisture. Replacing a damaged seal restores the barrier needed to contain wash water and protect the drive shaft bearing area. This is an OEM part sourced directly from the manufacturer.
Tub-to-Pump Drain Hose – Part Number: 4738ER1002A
$66.13
In Stock
Tub-to-Pump Drain Hose
★★★★★
★★★★★
(16)
Part #4738ER1002A
Water leaves the washer tub through this flexible tub-to-pump drain hose before reaching the drain pump housing. Its corrugated bellows section bends with tub movement, helping maintain the connection during washing and spinning. Cracks, punctures, or worn folds may allow water to leak beneath the appliance, while a collapsed section can restrict drainage. Replacing a damaged hose restores the enclosed path between the tub and pump, helping water drain properly while accommodating movement between the suspended tub and the pump assembly. This is an OEM part sourced directly from the manufacturer.
Door Lock Assembly – Part Number: EBF49827801
$82.45
In Stock
Door Lock Assembly
★★★★★
★★★★★
(29)
Part #EBF49827801
Secure door locking allows a front load washer to begin and complete its cycles. This door lock and switch assembly holds the door closed during operation and reports its status to the main control board. A failed lock or internal switch may prevent a cycle from starting, trigger a door fault message, or keep the door from unlocking after the cycle ends. Replacing a faulty assembly helps restore reliable locking and status feedback, supporting controlled access to the drum during washing and spinning. This is an OEM part sourced directly from the manufacturer.
Detergent Dispenser – Part Number: 3891ER2003A
$25.83
In Stock
Detergent Dispenser
★★★★★
★★★★★
(20)
Part #3891ER2003A
Liquid detergent stays contained in this removable dispenser cup until water flushes it into the washer during the wash cycle. The blue plastic insert sits inside the main detergent drawer and can be lifted out for cleaning. Cracks, damaged edges, or a missing cup may prevent liquid detergent from being held properly before dispensing. Replacing a damaged insert restores the container used for liquid detergent in the dispenser drawer. Its removable design also makes it easier to rinse away residue that collects with regular use. This is an OEM part sourced directly from the manufacturer.
Inlet Valve Assembly – Part Number: 5221ER1003A
$133.63
In Stock
Inlet Valve Assembly
★★★★★
★★★★★
(98)
Part #5221ER1003A
Cold water reaches the washer tub and dispenser through this triple-solenoid inlet valve assembly. Its three controlled outlets open during selected cycle stages, directing water where needed before closing to stop the flow. A damaged housing or failed valve mechanism may cause slow filling, no cold water, leaks, or water entering the drum while the washer is off. Replacing a faulty assembly helps restore controlled filling and reliable shutoff, supporting normal washing, rinsing, and delivery of laundry products from the dispenser. This is an OEM part sourced directly from the manufacturer.
Washer Hose with Bellows – Part Number: 4738ER1004B
$43.95
In Stock
Washer Hose with Bellows
★★★★★
★★★★★
(12)
Part #4738ER1004B
Water and detergent travel from the dispenser into the washer tub through this flexible rubber dispenser hose. Its bellows folds allow the hose to flex as the tub moves during operation, helping maintain the connection between the dispenser and tub. Cracks, tears, or worn sections may allow water to drip inside the cabinet, especially during filling. Replacing a damaged hose restores the enclosed path that carries the detergent mixture into the wash tub and helps prevent leaks from the hose body. This is an OEM part sourced directly from the manufacturer.
Washer Tub Bearing, Rear – Part Number: 4280EN4001F
$72.00
In Stock
Washer Tub Bearing, Rear
Part #4280EN4001F
Tub Bearing – Part Number: 4280FR4048L
No Longer Available
Tub Bearing
Part #4280FR4048L
The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, there could be an issue with the tub bearing. This genuine OEM replacement bearing has a 3-inch outer diameter, and is used to help the tub spin smoothly and to stop the washing machine from shaking during the cycle. NOTE: This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly at the same time.
Washer Tub Bearing – Part Number: MAP61913708
$56.33
Special Order
Washer Tub Bearing
★★★★★
★★★★★
(1)
Part #MAP61913708
Tub bearing. This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly.
Drain Hose Assembly – Part Number: 5215ER2002G
$46.29
In Stock
Drain Hose Assembly
★★★★★
★★★★★
(3)
Part #5215ER2002G
The drain hose assembly is a genuine OEM assembly supplied directly by LG for use in washing machines. The assembly includes the hose, connector, elbow fitting, and metal clamp. It is responsible for directing wastewater from the washing machine tub to the household drain or plumbing system. It allows the water to exit the washer efficiently and prevents it from pooling inside the machine at the end of the cycle. If the hose can no longer stay attached to the washer or drainpipe, water is leaking from the hose, or the hose has visible damage such as cracks and splits then you will need to replace it before you can resume using your washer.
Locking Pin – Part Number: 4774FR3118B
$25.75
Special Order
Locking Pin
★★★★★
★★★★★
(2)
Part #4774FR3118B
This is a locking pin, and it works in conjunction with your washer. The part measures to be roughly 3 inches long, and less than an inch wide. The pin is cylindrical, off-white in color, and made entirely of plastic. This part is used to hold the shock absorber on the washing machine. There is a pin used at the bottom and top of the shock absorber. This model is sold individually. If your washing machine is experiencing an above-average amount of shaking and moving this part may be the reason.

Questions And Answers for 79641373211

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
GALE - For model number 79641373211
November 20, 2024
WASHER STOPS SPINNING OR WON'T START SPINNING
Chris Boyle Profile
Hi Gale, Thank you for reaching out. This is normally an indication the Lid Switch is fault. If the switch has shorted out and not locking, it is no longer delivering the message to the machine and it will not latch into place. If you find that your door will not close, open, or start, it is more than likely an issue with the locker switch assembly. We hope this helps!
$82.45
In Stock
Door Lock Assembly
3 people found this instruction helpful.
Was this helpful?
Thank you for voting!
Rachel - For model number 79641373211
November 6, 2024
Hello I am looking for the front loader washer rubber that has gotten moldy. What part would this be to replace it? Thank you
Chris Boyle Profile
Hi Rachel, Thank you for your question. The part number for the bellow or door gasket is PS12391783. We hope this helps!
$283.32
In Stock
GASKET
Was this helpful?
Thank you for voting!
  • 1

Common Symptoms of the 79641373211

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
leaking tub-to-pump drain hose
53 of 77 people found this instruction helpful.
  • Leslie from STOWE, VT
  • Easy
  • 30 - 60 mins
  • Screw drivers
Pull washer away from wall. Unplug cord and remove drain hose from receptacle. Remove 4 screws holding panel to rear of washer. Squeeze and slide back hose clamps on each end of drain hose and loosen center clamp with screwdriver. Remove old hose. Reinstall new hose in reverse order using existing clamps. Re-install back panel.
Was this helpful?
Thank you for voting!
Inlet valve leak
34 of 37 people found this instruction helpful.
  • John from Northport, NY
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Followed directions on the video and went like a charm. Very impressed with service and video
Was this helpful?
Thank you for voting!
Door locking mechanism
28 of 36 people found this instruction helpful.
  • Aaron from SAN ANTONIO, TX
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
I received the locking device. I received an email from parts select with a repair video link. I watch the video and repeated the steps. Very easy and educational. Thank you for simplifying something I have limited experience doing.
Was this helpful?
Thank you for voting!