EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

79641172211 Kenmore Washer - Overview

Diagrams for 79641172211

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washing Machine Drain Pump – Part Number: 4681EA2001T
$61.55
In Stock
Washing Machine Drain Pump
★★★★★
★★★★★
(315)
Part #4681EA2001T
The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after the spin cycle speed is maintained for a specific period of time. To make this installation you will need a Phillips screwdriver, a small flat-blade screwdriver, a pair of needle-nose pliers, and a pair of slip-joint pliers. Note that the pump casing is not included. This medium-difficulty repair may vary, but can generally be started by disconnecting power, then removing the top of the washer by taking out the four back screws and two small brackets. Then, remove the front panel by taking out the two screws and eight tabs that should be taken from the top. Moving down the front of the washer, remove the door, latch, tub gasket, and drain cover. Disconnect the drain hoses and clip from under the drain assembly, and install new assembly from there. Reassemble parts in direct reverse order -- taking photos during disassembly and keeping parts clearly organized can help here. Despite the number of steps, you will only need a standard Phillips screwdriver to complete this repair.
Water Inlet Valve - Hot – Part Number: 5220FR2006H
$37.35
In Stock
Water Inlet Valve - Hot
★★★★★
★★★★★
(94)
Part #5220FR2006H
Hot water enters the washer through this single solenoid inlet valve, which opens when the control calls for hot water and closes when filling stops. It connects the household hot water supply to the internal fill system, regulating flow during selected wash cycles. A faulty valve may prevent hot water from entering, cause slow filling, or allow water to seep into the tub while the washer is off. Replacing a damaged valve helps restore controlled filling and proper shutoff of the hot water supply. This is an OEM part sourced directly from the manufacturer.
Rear Tub Gasket – Part Number: 4036ER2004A
$36.25
In Stock
Rear Tub Gasket
★★★★★
★★★★★
(15)
Part #4036ER2004A
Protecting the tub bearings from wash water, this rear tub shaft seal forms a barrier around the rotating drum shaft. The rubber seal fits into the rear outer tub and helps keep water and detergent away from the bearing area while the drum turns. A worn, torn, or hardened seal may allow leaks near the rear of the tub and expose the bearings to moisture. Replacing a damaged seal restores the barrier needed to contain wash water and protect the drive shaft bearing area. This is an OEM part sourced directly from the manufacturer.
Washer Door Boot Seal – Part Number: 4986ER0004F
$64.40
In Stock
Washer Door Boot Seal
★★★★★
★★★★★
(31)
Part #4986ER0004F
A flexible barrier around the washer opening keeps wash water contained while the tub moves. This front load washer door boot seal connects the outer tub to the front panel, using folded rubber to accommodate movement during washing and spinning. A built-in drain port allows residual water to leave the bottom of the seal. Tears, punctures, or worn sections may cause leaks around the door area. Replacing a damaged boot restores the sealing surface and helps contain water throughout the wash cycle. This is an OEM part sourced directly from the manufacturer.
Tub-to-Pump Drain Hose – Part Number: 4738ER1002A
$66.13
In Stock
Tub-to-Pump Drain Hose
★★★★★
★★★★★
(16)
Part #4738ER1002A
Water leaves the washer tub through this flexible tub-to-pump drain hose before reaching the drain pump housing. Its corrugated bellows section bends with tub movement, helping maintain the connection during washing and spinning. Cracks, punctures, or worn folds may allow water to leak beneath the appliance, while a collapsed section can restrict drainage. Replacing a damaged hose restores the enclosed path between the tub and pump, helping water drain properly while accommodating movement between the suspended tub and the pump assembly. This is an OEM part sourced directly from the manufacturer.
Door Lock Assembly – Part Number: EBF49827801
$82.45
In Stock
Door Lock Assembly
★★★★★
★★★★★
(29)
Part #EBF49827801
Secure door locking allows a front load washer to begin and complete its cycles. This door lock and switch assembly holds the door closed during operation and reports its status to the main control board. A failed lock or internal switch may prevent a cycle from starting, trigger a door fault message, or keep the door from unlocking after the cycle ends. Replacing a faulty assembly helps restore reliable locking and status feedback, supporting controlled access to the drum during washing and spinning. This is an OEM part sourced directly from the manufacturer.
Detergent Dispenser – Part Number: 3891ER2003A
$25.83
In Stock
Detergent Dispenser
★★★★★
★★★★★
(20)
Part #3891ER2003A
Liquid detergent stays contained in this removable dispenser cup until water flushes it into the washer during the wash cycle. The blue plastic insert sits inside the main detergent drawer and can be lifted out for cleaning. Cracks, damaged edges, or a missing cup may prevent liquid detergent from being held properly before dispensing. Replacing a damaged insert restores the container used for liquid detergent in the dispenser drawer. Its removable design also makes it easier to rinse away residue that collects with regular use. This is an OEM part sourced directly from the manufacturer.
Inlet Valve Assembly – Part Number: 5221ER1003A
$133.63
In Stock
Inlet Valve Assembly
★★★★★
★★★★★
(98)
Part #5221ER1003A
Cold water reaches the washer tub and dispenser through this triple-solenoid inlet valve assembly. Its three controlled outlets open during selected cycle stages, directing water where needed before closing to stop the flow. A damaged housing or failed valve mechanism may cause slow filling, no cold water, leaks, or water entering the drum while the washer is off. Replacing a faulty assembly helps restore controlled filling and reliable shutoff, supporting normal washing, rinsing, and delivery of laundry products from the dispenser. This is an OEM part sourced directly from the manufacturer.
Washer Hose with Bellows – Part Number: 4738ER1004B
$43.95
In Stock
Washer Hose with Bellows
★★★★★
★★★★★
(12)
Part #4738ER1004B
Water and detergent travel from the dispenser into the washer tub through this flexible rubber dispenser hose. Its bellows folds allow the hose to flex as the tub moves during operation, helping maintain the connection between the dispenser and tub. Cracks, tears, or worn sections may allow water to drip inside the cabinet, especially during filling. Replacing a damaged hose restores the enclosed path that carries the detergent mixture into the wash tub and helps prevent leaks from the hose body. This is an OEM part sourced directly from the manufacturer.
Washer Tub Bearing, Rear – Part Number: 4280EN4001F
$72.00
In Stock
Washer Tub Bearing, Rear
Part #4280EN4001F
Washer Tub Bearing – Part Number: MAP61913708
$56.33
Special Order
Washer Tub Bearing
★★★★★
★★★★★
(1)
Part #MAP61913708
Tub bearing. This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly.
Locking Pin – Part Number: 4774FR3118B
$25.75
Special Order
Locking Pin
★★★★★
★★★★★
(2)
Part #4774FR3118B
This is a locking pin, and it works in conjunction with your washer. The part measures to be roughly 3 inches long, and less than an inch wide. The pin is cylindrical, off-white in color, and made entirely of plastic. This part is used to hold the shock absorber on the washing machine. There is a pin used at the bottom and top of the shock absorber. This model is sold individually. If your washing machine is experiencing an above-average amount of shaking and moving this part may be the reason.

Questions And Answers for 79641172211

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:
  • 1
  • 2
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Deborah - For model number 79641172211
January 19, 2020
Washer when turned only blinks. Shows no codes. Does not come on. Just blinks. What could this be?
Chris Boyle Profile
Hello and thank you for writing. It certainly sounds like it could be a faulty door lock assembly PS3533609 and/or possibly a faulty drain pump and motor assembly PS3579318, you should check for signs of damage, and replace as necessary. We hope this helps. Please contact us anytime if you require further assistance.
$82.45
In Stock
Door Lock Assembly
$61.55
In Stock
Washing Machine Drain Pump
2 people found this instruction helpful.
Was this helpful?
Thank you for voting!
Deborah - For model number 79641172211
January 19, 2020
How can you tell if the display board is out?
Chris Boyle Profile
Hello and thank you for writing. You would have to test and diagnose the board with the help of a multimeter. We hope this helps. Please contact us anytime if you require further assistance.
1 person found this instruction helpful.
Was this helpful?
Thank you for voting!
Amanda - For model number 79641172211
March 25, 2024
My washer when I put a load in will not fill up completely clothes come out still dry but when I put the washing cleaning cycle on the washer will fill up but won’t fill up as it should on a wash cycle
Chris Boyle Profile
Hello Amanda, thank you for the question. Based on the description, the issue is mostly probably due to a faulty pressure switch assembly, part number PS3598722. We would recommend checking it to fix the issue. We hope this solves your problem!
$80.25
In Stock
Pressure Switch Assembly
Was this helpful?
Thank you for voting!
Romeo - For model number 79641172211
May 29, 2024
If I order the hot and cold water inlet valves are the solenoid included?
Chris Boyle Profile
Hi Romeo, thank you for your inquiry. Yes, the solenoids are included with both the water inlet valves. We hope this information is useful!
Was this helpful?
Thank you for voting!
Ronald - For model number 79641172211
August 28, 2025
Where can I get the travel bolts for this unit.
Chris Boyle Profile
Hi Ronald, thank you for your inquiry. The travel or shipping bolts, you are looking for is part number PS11711031. Glad to be of help!
$48.35
In Stock
Washer Bolt Assembly
Was this helpful?
Thank you for voting!
  • 1
  • 2

Common Symptoms of the 79641172211

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washing maching wouldn't drain
592 of 761 people found this instruction helpful.
  • Jorge from Apple Valley, CA
  • Easy
  • 1- 2 hours
  • Screw drivers
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer cam e apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Was this helpful?
Thank you for voting!
noisy operation, sometimes did not drain, gave OE code
60 of 81 people found this instruction helpful.
  • Michael from RALEIGH, NC
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman.
Was this helpful?
Thank you for voting!
leaking tub-to-pump drain hose
53 of 77 people found this instruction helpful.
  • Leslie from STOWE, VT
  • Easy
  • 30 - 60 mins
  • Screw drivers
Pull washer away from wall. Unplug cord and remove drain hose from receptacle. Remove 4 screws holding panel to rear of washer. Squeeze and slide back hose clamps on each end of drain hose and loosen center clamp with screwdriver. Remove old hose. Reinstall new hose in reverse order using existing clamps. Re-install back panel.
Was this helpful?
Thank you for voting!