This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stopping in the middle of a cycle, you may need to replace the water inlet valve. Be sure to disconnect the power and water supply before you begin this repair.
This part is known as a pulsator cap or washplate cap, and is designed for your LG washer. It fits over the washplate mounting bolt and prevents clothes from getting caught on the washplate during a wash cycle. It is round in shape, and approximately 3 inches in diameter.
This is a pulsator assembly, also known as an agitator, for your washing machine. This pulsator sits at the bottom of your washer and is what is used as the main driving force to wash your clothes. If the pulsator in your washer is broken, it will need replacing immediately to continue to wash and clean your clothes evenly. The cap that sits in the center of this part is sold separately.
This drain pump assembly is a genuine replacement part designed for select LG and Kenmore washing machines. It plays a critical role in removing water from the washer tub during the drain cycle, ensuring efficient water evacuation and proper cycle completion. Powered by an 85-watt, 120-volt motor, the pump is typically located near the dr...Read moreain hose at the bottom of the appliance. A failing pump may result in water remaining in the tub, incomplete draining, or unusual grinding or knocking noises during operation. Replacing the pump restores proper drainage and helps prevent water damage or cycle interruptions. Installation should be performed with the washer unplugged and may require basic tools and moderate repair experience.
This is a drain hose assembly for top-load models of LG washing machines. This hose specifically is used to allow water to drain from the tub to the drain pump of the washer. This hose is made of plastic and comes with two clamps to secure it within your washer, one on each end. If you notice your washer is leaking check to make sure if t...Read morehis hose is cracked or damaged, because it will need to be replaced immediately. This drain hose is an OEM part that is sold individually and will require you to disassemble part of your washer to replace it.
This drain hose is a genuine OEM replacement part supplied by LG for use in their washing machines. It is a light gray pipe with a diameter of 1.25 inches. The drain hose is connected to the drain pump, and it is responsible for transporting water out of the washing machine after a cycle. If the drain hose is kinked, damaged, or clogged, ...Read morethe washer will leak, or you may find standing water in the drum at the end of the cycle. Each drain hose comes with a metal clamp for fastening.
This water-level pressure switch in your wash monitors and regulates the water levels throughout the fill, wash, and rinse cycles. You will usually find it inside the control panel or near the tub. It ensures that the washer uses the appropriate amount of water for each cycle and load type. This genuine OEM assembly includes not only the switch itself but also the accompanying air dome tube.
This part is the replacement switch assembly for your top-load washer. It contains the switch mechanism and the connecting wire that hooks the door latch to the electrical system of the washer. The lid switch holds lets your washer know when the door is latched, so it can begin the wash cycle. If the lid switch is damaged, it will not all...Read moreow the washer to run properly. Be sure to disconnect the washer from the power and water sources before you begin this repair. This part is sold individually and is a genuine OEM part sourced directly from the manufacturer.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Michael - For model number 79631553610
February 12, 2025
My tub cover gasket is leaking. How do I order one ? What is the part number?
Hello Michael, Thank you for your inquiry. We show the compatible tub cover gasket as part# PS12077179. You can order through our site or by calling our customer service directly. We hope this helps you.
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
Keith - For model number 79631553610
June 13, 2025
selector knob spins and may finally land on wash selection after many tries
Hi Keith, thank you for reaching out. We would suggest checking the knob for any damage first. If it is fine, the issue could be with the display board, part number PS12080839. You may need to replace it to fix the issue. We hope this solves your problem!
Do the control panel button sponges come separately or do you have to buy the whole control panel just to replace faulty sponges
Hi Wilbur, thank you for reaching out. The control panel button sponges do not come separately. They come attached to the front panel assembly, part number PS12078615. You may need to replace it to fix the issue. We hope this solves your problem!
Hello Alesia, thank you for getting in touch. According to our research, the display board you are looking for is part number PS12080839. We hope this helps.
Hi Wayne, thank you for getting in touch. We would suggest checking the control board, part number EBR79203408. If it is malfunctioning, it fails to process the signal that the spin sequence should be completed. It gets stuck in a logic loop ramping the motor up, failing to log the completion, slowing it down, and trying again. You may need to replace it to fix the issue. We hope this solves your problem!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
It did not drain water, cycle stops at rinse+spin.
28 of 36 peoplefound this instruction helpful.
Jesus from El Paso, TX
Very Easy
15 - 30 mins
Socket set, Wrench set
1-Take water off manually. 2- Take machine to back yard. 3- lay machine 45 degrees. 4- Located water bump, (rear left side). 5-removed drain black hoses with hand. 6-removed 3 screws from bump frame. 7-Taker off all unit and marked down cable position at plug. 8- installed new pump. 9- Reverse all steps. Note: I did not use new cable su
... Read morepplied with the new bump, I did not want to mess around on mother board connections, I kept old wire harness which are only two cables blue and gray. It took me less than 30 minutes.
Read less
Was this helpful?
Thank you for voting!
Water continued leaking into washer after the end of cycle through the water inlet valve.
14 of 19 peoplefound this instruction helpful.
Flora from MIAMI, FL
Very Easy
30 - 60 mins
Screw drivers, Wrench (Adjustable)
Did the repair Myself. Saved $ 400.00 in the process.
Was this helpful?
Thank you for voting!
Water overflow in washer basin
11 of 15 peoplefound this instruction helpful.
Ed from LAKE WORTH, FL
Really Easy
30 - 60 mins
Pliers, Screw drivers
I diagnosed by running a full wash. I watched it and when the water should have stopped it kept running. I unplugged the washer from the power and the water kept running. This told me the inlet valve was the issue and not an electronic issue. I stopped the water by closing the water valve manually. Replacing the inlet valve was very easy
... Read more. Hardest part is moving the washer out of the laundry room. The videos online show very simple steps. Maybe 8 screws to remove and a couple of hoses and five electronic connectors. Take a photo of connectors before removing them to ensure you reconnect properly.
My Orders
