This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stopping in the middle of a cycle, you may need to replace the water inlet valve. Be sure to disconnect the power and water supply before you begin this repair.
Clothing moves over a covered mounting point with help from this washer pulsator cap. The round plastic cover snaps into the center of the washplate, concealing the mounting bolt and providing a smooth surface above it. Cracks, broken retaining tabs, or a missing cap may expose the hardware or allow the cover to come loose during washing....Read more Replacing a damaged cap restores the finished washplate surface and helps keep garments from catching around the recessed bolt opening as laundry moves through the wash cycle. This is an OEM part sourced directly from the manufacturer.
This is a pulsator assembly, also known as an agitator, for your washing machine. This pulsator sits at the bottom of your washer and is what is used as the main driving force to wash your clothes. If the pulsator in your washer is broken, it will need replacing immediately to continue to wash and clean your clothes evenly. The cap that sits in the center of this part is sold separately.
Drain used wash water with this top-load washer drain pump assembly. Its motor drives an internal impeller that pushes water from the tub through the drain hose during drain and spin cycles. A worn motor, damaged impeller, or leaking housing may cause standing water, slow draining, loud buzzing, or puddles beneath the machine. Replacing a...Read more faulty pump helps restore proper drainage so wash cycles can finish normally. Unplug the washer, shut off the water supply, and prepare for leftover water before disconnecting hoses or wiring. This is an OEM part sourced directly from the manufacturer.
This washer tub-to-pump drain hose carries used water from the outer tub to the drain pump during draining. Its flexible, corrugated design accommodates tub movement while keeping water contained within the drainage path. Cracks, splits, or worn sections may cause leaks beneath the washer, while a collapsed section can restrict flow and l...Read moreeave water in the tub. Replacing a damaged hose helps restore proper drainage and a secure connection between the tub and pump, allowing wastewater to move out during wash and rinse cycles. This is an OEM part sourced directly from the manufacturer.
This drain hose is a genuine OEM replacement part supplied by LG for use in their washing machines. It is a light gray pipe with a diameter of 1.25 inches. The drain hose is connected to the drain pump, and it is responsible for transporting water out of the washing machine after a cycle. If the drain hose is kinked, damaged, or clogged, ...Read morethe washer will leak, or you may find standing water in the drum at the end of the cycle. Each drain hose comes with a metal clamp for fastening.
Secure attachment of washer components depends on fasteners that hold firmly during operation. This replacement washer screw restores an attachment where the original screw is missing, stripped, or damaged. Worn threads or a damaged head may prevent proper tightening and leave the attached component loose. Replacing faulty hardware helps ...Read morerestore a firm connection when the receiving threads and surrounding material remain intact. The screw can also be replaced during reassembly if damage prevents the original fastener from being tightened or removed normally. This is an OEM part sourced directly from the manufacturer.
Accurate water level sensing helps the washer fill and advance through its cycles correctly. This pressure sensor assembly measures changes in air pressure through a connected tube as water enters or leaves the tub. It sends water level information to the electronic control so filling can stop at the required level. A faulty sensor may ca...Read moreuse overfilling, underfilling, or interrupted wash cycles. Replacing a failed assembly helps restore reliable level feedback and controlled filling throughout the wash and rinse stages. This is an OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
It did not drain water, cycle stops at rinse+spin.
28 of 36 peoplefound this instruction helpful.
Jesus from El Paso, TX
Very Easy
15 - 30 mins
Socket set, Wrench set
1-Take water off manually. 2- Take machine to back yard. 3- lay machine 45 degrees. 4- Located water bump, (rear left side). 5-removed drain black hoses with hand. 6-removed 3 screws from bump frame. 7-Taker off all unit and marked down cable position at plug. 8- installed new pump. 9- Reverse all steps. Note: I did not use new cable su
... Read morepplied with the new bump, I did not want to mess around on mother board connections, I kept old wire harness which are only two cables blue and gray. It took me less than 30 minutes.
Read less
Was this helpful?
Thank you for voting!
Water continued leaking into washer after the end of cycle through the water inlet valve.
14 of 19 peoplefound this instruction helpful.
Flora from MIAMI, FL
Very Easy
30 - 60 mins
Screw drivers, Wrench (Adjustable)
Did the repair Myself. Saved $ 400.00 in the process.
Was this helpful?
Thank you for voting!
Water overflow in washer basin
11 of 15 peoplefound this instruction helpful.
Ed from LAKE WORTH, FL
Really Easy
30 - 60 mins
Pliers, Screw drivers
I diagnosed by running a full wash. I watched it and when the water should have stopped it kept running. I unplugged the washer from the power and the water kept running. This told me the inlet valve was the issue and not an electronic issue. I stopped the water by closing the water valve manually. Replacing the inlet valve was very easy
... Read more. Hardest part is moving the washer out of the laundry room. The videos online show very simple steps. Maybe 8 screws to remove and a couple of hoses and five electronic connectors. Take a photo of connectors before removing them to ensure you reconnect properly.