7957802 Kenmore Refrigerator - Overview

The interior light in your refrigerator is controlled by a switch that is activated when the door is opened and closed. If your refrigerator light will not turn on, or stays on when the door is closed, you could have a faulty switch. The switch is spring-loaded and is a generally closed type of switch meaning there should be no continuity...Read more when the button is pushed, and continuity through the switch when it is no longer engaged. This plastic, white, OEM switch is sourced directly from the manufacturer, is sold individually and is easy to replace. The repair usually takes less than 15 minutes and requires a flat-blade screwdriver and needle-nose pliers.

This genuine refrigerator pantry drawer front cover provides a finished front panel for the pantry or deli drawer while helping keep stored foods organized and protected. Made from durable clear plastic with decorative trim, it serves as a replacement for a cracked, damaged, or worn drawer front and helps maintain smooth drawer operation ...Read moreand a clean appearance inside the refrigerator. The cover measures approximately 17 inches wide, 7 inches high, and 1 inch deep.

This refrigerator door hinge bushing is a durable white plastic component that provides a smooth pivot point for the hinge pin, helping keep the door properly aligned and sealed. It is commonly used to correct doors that sag, make noise, or are difficult to open or close due to a worn or damaged bushing. The bushing installs at the door h...Read moreinge pivot point and typically requires removing the hinge bracket with a 10?mm socket. Color is white, and size and dimensions may vary by refrigerator model.

This ice maker assembly is for refrigerators. This Ice maker assembly contains the complete ice maker and housing. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.

This is a genuine replacement switch. It is a push button style switch that is designed for use in your refrigerator. When the door of your appliance is opened the switch is released, and the light comes on. When you close the door the switch is pressed in, and the light turns off. You may need a putty knife to remove your old switch.

This is a genuine OEM evaporator motor that directly powers the evaporator mechanism within your refrigerator. This mechanism is responsible for pulling air over the evaporator coils, which are cold, and circulating that cold air back throughout the appliance. Without this motor, the interior of your refrigerator would build up frost, str...Read moreain the compressor, and simply not cool your fridge enough. A warm fridge, frost buildup or unusual noises are all signs that this fan needs replacing, and over time or through excessive dust building up, motor issues will arise and can cause it to fail. This fan motor is sold as an individual part, so it does not come with any securing screws or the fan blade itself. Replacing the evaporator fan motor will require your user manual and Philips-head and flathead screwdrivers. You need to gain access to the evaporator cover, which you will need to locate using your user manual schematics. Once the cover is removed and you disconnect the wire harnesses within it, you can disassemble the fan mechanism on its inside portion. With the fan mechanism disassembled, remove the old mechanism and install the new one, with the securing screws and wire harnesses.

This part must be installed by a licensed and trained LG technician that is able to perform a software update, which is required for the installation of this compressor. Part number CJT30000002 is needed to perform the update. Also, the three pins on the side of the new compressor may be oriented differently than the original. If diff...Read moreerent, when installing the new compressor the compressor electrical connector must be rotated 45 degrees counter-clockwise.

This is a temperature sensor for various models of LG refrigerators. Temperature sensors are used to adjust the level of cooling depending on the internal temperature of the refrigerator. If your refrigerator is warm or not cooling consistently, ensure your evaporator fan is not blocked, before replacing this sensor. To replace this senso...Read morer, you will need a screwdriver and a set of pliers, and simply need to unplug the old sensor, and plug in the new one. This temperature sensor is a genuine OEM part that is sold individually and does not come with any other parts or accessories.

This genuine OEM refrigerator door basket is a durable white plastic bin designed to mount on the inside of the refrigerator door, providing convenient storage for jars, bottles, and condiments. It helps keep items organized and easily accessible while making efficient use of door space. Replacing a cracked or broken door bin restores sec...Read moreure storage and improves everyday usability, with installation typically requiring no tools as the basket slides easily into place.

This handle screw, also known as a mounting screw is designed for LG fridge door handles. It Is responsible for securing the handle to the fridge door and ensuring that it remains firmly attached. A secure door handle allows you to easily open and close the refrigerator as needed. Over time the screw may break, become corroded, or the thr...Read moreeads may wear down. If this happens, the handle may become loose or wobbly, or detach completely from the door. It is recommended to replace the handle screw if it is no longer in good working condition in order to avoid potential damage to the door panel. Each handle screw is sold individually.