This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as ...Read morethey commonly wear at the same rate. This is about 1 inch long and metallic in color.
This door basket assembly is supplied by the original manufacturer to provide storage for various food items in refrigerators. It consists of a white plastic base and a transparent shield, measuring 14.5 inches in length and 4 inches in width. The basket is securely attached to the right side of the refrigerator and offers a compartment f...Read moreor organizing items such as bottles, jars, and condiments. The door basket assembly helps maximize storage space and allows you to easily access frequently used items. However, the door basket will need to be replaced if the plastic becomes cracked, deformed, or broken. Using a faulty door basket may result in items falling out, and potential damage to the door frame. Detach the old basket assembly from the refrigerator and snap the new one in place. Ensure that the new assembly is securely fitted before placing items in it.
This air filter assembly is a genuine replacement part designed to improve air quality inside select LG and Kenmore Elite refrigerators. Using activated carbon, it effectively traps and neutralizes odors and airborne impurities, helping maintain a clean environment that supports longer food freshness. The filter is housed within a dedicat...Read moreed compartment and should be replaced approximately every six months or when indicated by the refrigerator’s filter light. Installation involves locating the filter housing, powering off the appliance, removing the old filter, and inserting the new one with proper alignment. After installation, reassemble the housing, restore power, and reset the filter indicator to ensure accurate tracking. This OEM component ensures a precise fit and optimal performance for compatible models.
This is a manufacturer-approved refrigerator door closure for your refrigerator. It is made of white plastic and measures approximately 3 inches by 2 inches. If your old closure is damaged, your refrigerator door may not open and shut properly, and therefore it should be replaced.
This glass shelf provides storage space in your refrigerator above the crisper. Shelves can crack and chip due to frequent use, and should be replaced immediately if cracks start to appear. This shelf measures approximately 30.5 inches wide by 15 inches deep and is for LG refrigerators. Replacing a damaged shelf is easy, carefully remove ...Read morethe faulty shelf and install the new one. Be sure to wear protective gloves if the existing shelf is cracked or broken.
This is a micro switch for various models of LG refrigerators. This switch is responsible for turning the ice dispenser on and off within the freezer compartment of the fridge. If this switch is damaged or shorted, it will cause the ice maker to work inconsistently, or not at all. This switch is different from the water dispenser switch, ...Read morewhich has an entirely different shape all together. Replacing this switch is simple and only requires a Philips-head screwdriver to disconnect the old switch and install the new one. This switch is a genuine OEM LG part and does not come with any other parts or accessories.
This part must be installed by a licensed and trained LG technician that is able to perform a software update, which is required for the installation of this compressor. Part number CJT30000002 is needed to perform the update.
Also, the three pins on the side of the new compressor may be oriented differently than the original. If diff...Read moreerent, when installing the new compressor the compressor electrical connector must be rotated 45 degrees counter-clockwise.
This rail connector is a replacement structural component designed to join and stabilize sliding or support rails. It ensures smooth movement and alignment and is commonly replaced when worn or broken.
This water inlet valve in your refrigerator, also called a solenoid valve or water control valve, regulates water flow to the icemaker and dispenser. It is found at the rear of the appliance, where it connects to the household water supply line. It uses electrical solenoids to control the flow of water. It needs to be replaced when your f...Read moreridge has a lack of ice production, an inactive water dispenser, or water leaks around the supply line. Please keep in mind that this genuine OEM replacement part is sold separately from the water line.
This water tubing clip holds the water fill tube in place in your refrigerator. The water fill tube attaches and supplies water to the ice maker/water dispenser in your fridge-freezer. If the tubing is in working order, but is hanging loose inside the unit, the issue could be that the clip meant to hold it in place is broken. If this is t...Read morehe case, you should look to replace the clip. This clip is made of black plastic, and is just over half an inch long. This is a genuine OEM replacement part, and is sold separately.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice Maker Quit Making Ice
8 of 12 peoplefound this instruction helpful.
Jeff from HUMBLE, TX
Very Easy
Less than 15 mins
Screw drivers
For this model the ice maker is very easy to replace. All it takes is a phillips head screwdriver. There are two wire connections you have to unplug. Easy out easy in. You do not have to disconnect the water line, just make sure the line is lined up correctly when you reinstall the new icemaker. It seems to take approximately 8 hours befo
... Read morere you start getting ice again. If you have this same model, you already know this ice maker is very slow in making ice and is not able to keep up with daily usage of ice for a household of 3.
Read less
Was this helpful?
Thank you for voting!
Ice maker stopped working
4 of 5 peoplefound this instruction helpful.
Orlando from MESA, AZ
Easy
30 - 60 mins
Screw drivers
The Ice Maker from Part Select was complete. Plastic housing, Ice maker located at the top and ice cruncher/dispenser at the bottom. Note: Both the ice maker and the dispenser wiring goes to a common connecter. It is not advisable to plan changing out only one of these.
Was this helpful?
Thank you for voting!
Door stopper broke
5 of 9 peoplefound this instruction helpful.
ROGER from SCHELLSBURG, PA
Really Easy
Less than 15 mins
Screw drivers
Installed new door stopper with screw driver on bottom of french door