This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as ...Read morethey commonly wear at the same rate. This is about 1 inch long and metallic in color.
This refrigerator door bin provides handy storage for condiments, jars, bottles, and other small items. It attaches to the inside of the door, keeping everyday foods easy to reach while freeing up space on the main shelves. The raised sides help keep items in place as the door opens and closes. Cracks, broken mounting tabs, or a damaged b...Read morease may leave the bin loose or unable to hold items safely. Replacing a broken bin restores useful storage and helps keep your refrigerator organized. This is an OEM part sourced directly from the manufacturer.
This air filter assembly is a genuine replacement part designed to improve air quality inside select LG and Kenmore Elite refrigerators. Using activated carbon, it effectively traps and neutralizes odors and airborne impurities, helping maintain a clean environment that supports longer food freshness. The filter is housed within a dedicat...Read moreed compartment and should be replaced approximately every six months or when indicated by the refrigerator’s filter light. Installation involves locating the filter housing, powering off the appliance, removing the old filter, and inserting the new one with proper alignment. After installation, reassemble the housing, restore power, and reset the filter indicator to ensure accurate tracking. This OEM component ensures a precise fit and optimal performance for compatible models.
This is a manufacturer-approved refrigerator door closure for your refrigerator. It is made of white plastic and measures approximately 3 inches by 2 inches. If your old closure is damaged, your refrigerator door may not open and shut properly, and therefore it should be replaced.
This glass shelf provides storage space in your refrigerator above the crisper. Shelves can crack and chip due to frequent use, and should be replaced immediately if cracks start to appear. This shelf measures approximately 30.5 inches wide by 15 inches deep and is for LG refrigerators. Replacing a damaged shelf is easy, carefully remove ...Read morethe faulty shelf and install the new one. Be sure to wear protective gloves if the existing shelf is cracked or broken.
Keep frozen food protected from warm air leaks with this freezer door gasket. Its flexible sealing edge fits around the door perimeter and rests against the cabinet when closed, helping retain cold air and limit incoming moisture. Tears, cracks, or warped sections may cause frost buildup, condensation, or longer running times. Replacing a...Read more damaged gasket helps restore a snug seal. Before installation, smooth shipping creases with warm water and clean the retaining groove, then seat the corners first and check for even contact along every edge. This is an OEM part sourced directly from the manufacturer.
This is a micro switch for various models of LG refrigerators. This switch is responsible for turning the ice dispenser on and off within the freezer compartment of the fridge. If this switch is damaged or shorted, it will cause the ice maker to work inconsistently, or not at all. This switch is different from the water dispenser switch, ...Read morewhich has an entirely different shape all together. Replacing this switch is simple and only requires a Philips-head screwdriver to disconnect the old switch and install the new one. This switch is a genuine OEM LG part and does not come with any other parts or accessories.
This part must be installed by a licensed and trained LG technician that is able to perform a software update, which is required for the installation of this compressor. Part number CJT30000002 is needed to perform the update.
Also, the three pins on the side of the new compressor may be oriented differently than the original. If diff...Read moreerent, when installing the new compressor the compressor electrical connector must be rotated 45 degrees counter-clockwise.
This fridge gasket, also known as a door seal, is an authentic OEM part supplied by LG for use with various models of LG refrigerators. It is a flexible strip of rubber that sits along the perimeter of the refrigerator. It creates an airtight seal between the door and fridge body to prevent cold air from escaping and warm air from enterin...Read moreg. This helps to keep your fridge cool and energy efficient. If the gasket is worn out, torn, or can no longer maintain a tight seal, your fridge will have to work harder to maintain the correct temperature inside the fridge. You may also notice that the door may not be able to close properly.
This rail connector is a replacement structural component designed to join and stabilize sliding or support rails. It ensures smooth movement and alignment and is commonly replaced when worn or broken.
Water cools inside the refrigerator before dispensing with help from this reservoir tank assembly. The tank holds a supply of water in the fresh food compartment, allowing it to chill between uses. Cracks, punctures, or damaged connections may cause leaks inside the cabinet and interrupt delivery to the dispenser. Replacing a damaged rese...Read morervoir restores the enclosed storage path for chilled water. As water leaves the tank during dispensing, incoming water replenishes the supply so it can cool before the next use. This is an OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice Maker Quit Making Ice
8 of 12 peoplefound this instruction helpful.
Jeff from HUMBLE, TX
Very Easy
Less than 15 mins
Screw drivers
For this model the ice maker is very easy to replace. All it takes is a phillips head screwdriver. There are two wire connections you have to unplug. Easy out easy in. You do not have to disconnect the water line, just make sure the line is lined up correctly when you reinstall the new icemaker. It seems to take approximately 8 hours befo
... Read morere you start getting ice again. If you have this same model, you already know this ice maker is very slow in making ice and is not able to keep up with daily usage of ice for a household of 3.
Read less
Was this helpful?
Thank you for voting!
Ice maker stopped working
4 of 5 peoplefound this instruction helpful.
Orlando from MESA, AZ
Easy
30 - 60 mins
Screw drivers
The Ice Maker from Part Select was complete. Plastic housing, Ice maker located at the top and ice cruncher/dispenser at the bottom. Note: Both the ice maker and the dispenser wiring goes to a common connecter. It is not advisable to plan changing out only one of these.
Was this helpful?
Thank you for voting!
Door stopper broke
5 of 9 peoplefound this instruction helpful.
ROGER from SCHELLSBURG, PA
Really Easy
Less than 15 mins
Screw drivers
Installed new door stopper with screw driver on bottom of french door