This front plate assembly, also known as a mullion or flipper, is a genuine replacement part designed for select LG and Kenmore French-door refrigerators. It serves a critical function by sealing the gap between the doors, preventing cold air from escaping and helping maintain consistent internal temperatures. Constructed from durable pla...Read morestic, it supports both the performance and appearance of the appliance. A failing mullion may result in poor sealing, visible gaps, increased energy consumption, and potential food spoilage. Replacing this component can restore proper door alignment and improve overall efficiency. Compatibility should be confirmed using your refrigerator’s model number prior to installation.
This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as ...Read morethey commonly wear at the same rate. This is about 1 inch long and metallic in color.
Controlled door travel helps prevent a refrigerator door from swinging beyond its intended opening range. This white plastic door stopper mounts near the bottom of the door and provides a stopping point as it opens. A cracked, worn, or broken stopper may allow excessive movement or fail to stop the door normally. Replacing a damaged stopp...Read moreer helps restore the intended swing limit and reduces strain caused by overextension. The stopper works with the hinge assembly to provide a mechanical limit during everyday opening and closing. This is an OEM part sourced directly from the manufacturer.
This refrigerator water inlet valve assembly controls the water supplied to the dispenser and automatic ice maker. It opens when the appliance requests water and closes when dispensing or filling ends. A cracked housing or faulty valve may cause leaks, weak dispenser flow, or prevent the ice maker mold from filling. Replacing a failed ass...Read moreembly helps restore controlled water delivery and proper shutoff between uses. The valve connects the incoming supply to the internal water system, supporting everyday dispensing and ice production. This is an OEM part sourced directly from the manufacturer.
Automatic ice production is easy with this refrigerator ice maker assembly kit. It receives water from the inlet valve, holds it in the mold while it freezes, and releases finished cubes into the storage bin. A failed mechanism may stop making ice, leave cubes stuck in the mold, or make clicking and grinding noises during release. Replaci...Read moreng a faulty assembly helps restore a steady supply of ice without filling trays by hand. Unplug the refrigerator before removing or installing the unit. This is an OEM part sourced directly from the manufacturer.
This is a manufacturer-approved refrigerator door closure for your refrigerator. It is made of white plastic and measures approximately 3 inches by 2 inches. If your old closure is damaged, your refrigerator door may not open and shut properly, and therefore it should be replaced.
This is a micro switch for various models of LG refrigerators. This switch is responsible for turning the ice dispenser on and off within the freezer compartment of the fridge. If this switch is damaged or shorted, it will cause the ice maker to work inconsistently, or not at all. This switch is different from the water dispenser switch, ...Read morewhich has an entirely different shape all together. Replacing this switch is simple and only requires a Philips-head screwdriver to disconnect the old switch and install the new one. This switch is a genuine OEM LG part and does not come with any other parts or accessories.
This part must be installed by a licensed and trained LG technician that is able to perform a software update, which is required for the installation of this compressor. Part number CJT30000002 is needed to perform the update.
Also, the three pins on the side of the new compressor may be oriented differently than the original. If diff...Read moreerent, when installing the new compressor the compressor electrical connector must be rotated 45 degrees counter-clockwise.
Water cools inside the refrigerator before dispensing with help from this reservoir tank assembly. The tank holds a supply of water in the fresh food compartment, allowing it to chill between uses. Cracks, punctures, or damaged connections may cause leaks inside the cabinet and interrupt delivery to the dispenser. Replacing a damaged rese...Read morervoir restores the enclosed storage path for chilled water. As water leaves the tank during dispensing, incoming water replenishes the supply so it can cool before the next use. This is an OEM part sourced directly from the manufacturer.
This roller assembly supports smooth movement of racks, drawers, or drums during operation. Reduced friction improves ease of use and reduces wear. Replacing a worn roller restores quiet, smooth movement.
This genuine OEM cover is both a protective shield and an aesthetic front for the deli drawer in your refrigerator. It has a clear color and is typically in the lower section of the fresh food compartment. It can become worn with repeated use over time or break due to accidental drops. Your refrigerator has covers in different sizes, so be sure to purchase the correct one for your model.
This is a temperature sensor for various models of LG refrigerators. Temperature sensors are used to adjust the level of cooling depending on the internal temperature of the refrigerator. If your refrigerator is warm or not cooling consistently, ensure your evaporator fan is not blocked, before replacing this sensor. To replace this senso...Read morer, you will need a screwdriver and a set of pliers, and simply need to unplug the old sensor, and plug in the new one. This temperature sensor is a genuine OEM part that is sold individually and does not come with any other parts or accessories.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
replace leaking water inlet valve assembly
42 of 75 peoplefound this instruction helpful.
Richard from JACKSONVILLE, FL
Really Easy
15 - 30 mins
Screw drivers
1. Shut off water to refrigerator. 2. Removed bottom sheet metal cover (6 screws). 3. Removed leaking water inlet valve assembly from refrigerator (1 screw). 4. Remove water inlet tube (loosen nut) and tube back to refrigerator (pull from water valve after remove cotter pin washer). 5. Detach two electrical wire harnesses. 6. Install new
... Read morewater inlet valve assembly to refrigerator (1 screw). 7. Replace both water tubes to water inlet assembly. 8. Re-attach both wiring harnesses. 9. Turn water to refrigerator on. 10. Check for leaks. 11. Re-attach bottom sheet cover (6 screws).
Read less
Was this helpful?
Thank you for voting!
My nephew accidentally forced the door closed last year, which resulted in the door having to be re closed manually folding back the flap. Ugh!
25 of 46 peoplefound this instruction helpful.
Tiziana from WARWICK, NY
Really Easy
Less than 15 mins
Nutdriver
Unscered 2 screws, unplug electrical connection under the screws, slide her flap into grooves, realign screw holes , and rescrew in. Done.
Was this helpful?
Thank you for voting!
Error Code dH F
14 of 27 peoplefound this instruction helpful.
Garthlette from COVINGTON, GA
A Bit Difficult
30 - 60 mins
Screw drivers
The refrigerator had the above code and when I check on YouTube, it explained that the defrosting was not working properly. It was taking more than 80 minutes to defrost. I ordered the Temperature Sensor first and it was not the issue. I also ordered the Defrost Temperature fuse or the Thermistor. I had to defrost the refrigerator first
... Read more by using a portable heater to get it done quickly. (See Youtube on how to get to the Defrosting Unit inside the freezer). The Thermistor was the wrong part. I called the Partselect and explained that the part with the heating element is one piece. (Heating Coil Thermistor or Heating Coil). By replacing that piece solved the Error Code issue. I listened to Youtube for the instructions on how to replace the Heater Coil. So if you see the Error Code dH F, you need to replace the Heating Coil, which comes in one piece and sits on the bottom of the Defrost Element.