This refrigerator water filter replacement is for 2010 LG refrigerators that have either forward French doors or are the four-door dispensing models. This filter is designed to minimize impurities that can cause ill-tasting water or an unpleasant smell. It reduces sediment, dirt, rust, limescale, sand, and many other contaminants that can...Read more be harmful to your health and the life of your appliance. This filter should be replaced every 6 months or 200 gallons to ensure top quality performance.
To remove your unwanted filter, press the push button to open the filter cover (water may spill from the hole), pull out the old cartridge in a downward motion. To install the new filter, make it so the ears are in the horizontal position and push the new cartridge into the housing until it stops. Push the filter upward until it is secure. Click the cover to lock it in place. Run water for approximately 5 minutes to prep the filter for use, and discard water. Reset the “filter reset” button if applicable.
Add useful storage space inside a refrigerator door with this clear plastic door bin. It holds bottles, jars, drinks, and condiments where they are easy to see and reach. The bin measures about 13-1/2 inches wide and 4-1/4 inches high. Its shaped base is about 9-1/2 inches deep on one side and 10-1/8 inches deep on the other. Installation...Read more requires no tools. Place the bin slightly above the mounting points, then slide it down until it locks into place. Compare the size, shape, and side mounts with the original bin before ordering.
This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as ...Read morethey commonly wear at the same rate. This is about 1 inch long and metallic in color.
This refrigerator door bin provides handy storage for condiments, jars, bottles, and other small items. It attaches to the inside of the door, keeping everyday foods easy to reach while freeing up space on the main shelves. The raised sides help keep items in place as the door opens and closes. Cracks, broken mounting tabs, or a damaged b...Read morease may leave the bin loose or unable to hold items safely. Replacing a broken bin restores useful storage and helps keep your refrigerator organized. This is an OEM part sourced directly from the manufacturer.
This air filter assembly is a genuine replacement part designed to improve air quality inside select LG and Kenmore Elite refrigerators. Using activated carbon, it effectively traps and neutralizes odors and airborne impurities, helping maintain a clean environment that supports longer food freshness. The filter is housed within a dedicat...Read moreed compartment and should be replaced approximately every six months or when indicated by the refrigerator’s filter light. Installation involves locating the filter housing, powering off the appliance, removing the old filter, and inserting the new one with proper alignment. After installation, reassemble the housing, restore power, and reset the filter indicator to ensure accurate tracking. This OEM component ensures a precise fit and optimal performance for compatible models.
Proper movement of the center door flap helps a French door refrigerator seal the gap between its doors. This mullion spring applies tension to the hinged flap, guiding it as the door opens and closes. A broken, stretched, or missing spring may leave the flap loose or prevent it from moving into place, making door closure difficult. Repla...Read morecing a damaged spring helps restore controlled flap movement and proper sealing. Its coiled design stores and releases force as the mullion pivots during everyday use. This is an OEM part sourced directly from the manufacturer.
This is a manufacturer-approved refrigerator door closure for your refrigerator. It is made of white plastic and measures approximately 3 inches by 2 inches. If your old closure is damaged, your refrigerator door may not open and shut properly, and therefore it should be replaced.
Keep ice ready for everyday drinks with this refrigerator ice maker assembly. It receives water, holds it in the mold while it freezes, and releases finished cubes into the storage bin. A worn or failed mechanism may stop making ice, leave cubes stuck in the mold, or leak around the ice tray. Replacing a faulty assembly helps restore auto...Read morematic ice production without filling trays by hand. The attached wiring harness connects the unit to the refrigerator controls. Unplug the refrigerator before removing or installing the assembly. This is an OEM part sourced directly from the manufacturer.
This is a door seal, also known as a door gasket, for LG refrigerators. This door gasket is used to seal the warmer room temperature from the cooler fridge interior. If the gasket for your refrigerator is warped, moldy, or damaged in any way, it needs to be replaced immediately. To replace this gasket, simply pull off the old gasket to re...Read moremove it, and carefully wrap the new gasket around the door perimeter. This gasket is sold individually and does not include any other parts.
This is a micro switch for various models of LG refrigerators. This switch is responsible for turning the ice dispenser on and off within the freezer compartment of the fridge. If this switch is damaged or shorted, it will cause the ice maker to work inconsistently, or not at all. This switch is different from the water dispenser switch, ...Read morewhich has an entirely different shape all together. Replacing this switch is simple and only requires a Philips-head screwdriver to disconnect the old switch and install the new one. This switch is a genuine OEM LG part and does not come with any other parts or accessories.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replaced Old Molded Gasket with new one
9 of 9 peoplefound this instruction helpful.
Megan from Elk Grove, CA
Very Easy
Less than 15 mins
Screw drivers
For the right side of the refrigerator door, just pulled off the old gasket and replaced it with the new one. Old gasket came off easily. Just had to pull it off. No screws on the right side. Just pushed the new one in place in the groove on the door.
For the left side, needed a Phillip’s screwdriver to remove the flap first. H
... Read moreelps to have a second person hold the door from moving. Once flap was off, pulled the old gasket off and installed the new one just like the right side. Then screwed the flap back on once the gasket was in the groove properly.
Initially after install, it seemed like the magnet on the door was not strong enough but after a couple of days, the magnet seems a lot stronger, sealing the air out. Very happy I replaced it. It was a lot simpler to replace than I thought it would be.
Found the broken spring; matched it with parts diagram. Googled for sources via part number. Selected this site because it had best deal - price, availability, shipping. Part arrived as predicted; installed it in 2 minutes. Job done. Door now works.
Was this helpful?
Thank you for voting!
old one broke
9 of 17 peoplefound this instruction helpful.
Ron from MAXWELL, IN
Easy
30 - 60 mins
Screw drivers
Sent for replacement,got it took old one off put new one on that was it. Thank you