Opening the refrigerator door releases this push-button switch to turn on the interior light, making stored food easier to see. When the door closes, it presses the button and turns the light off. A stuck, worn, or broken switch may leave the light off when the door is open or keep it on after closing. Replacing a faulty switch helps rest...Read moreore normal lighting control and reliable response to door movement. Disconnect the refrigerator from power before removing or installing the switch. This is an OEM part sourced directly from the manufacturer.
This refrigerator water filter replacement is for 2010 LG refrigerators that have either forward French doors or are the four-door dispensing models. This filter is designed to minimize impurities that can cause ill-tasting water or an unpleasant smell. It reduces sediment, dirt, rust, limescale, sand, and many other contaminants that can...Read more be harmful to your health and the life of your appliance. This filter should be replaced every 6 months or 200 gallons to ensure top quality performance.
To remove your unwanted filter, press the push button to open the filter cover (water may spill from the hole), pull out the old cartridge in a downward motion. To install the new filter, make it so the ears are in the horizontal position and push the new cartridge into the housing until it stops. Push the filter upward until it is secure. Click the cover to lock it in place. Run water for approximately 5 minutes to prep the filter for use, and discard water. Reset the “filter reset” button if applicable.
Add useful storage space inside a refrigerator door with this clear plastic door bin. It holds bottles, jars, drinks, and condiments where they are easy to see and reach. The bin measures about 13-1/2 inches wide and 4-1/4 inches high. Its shaped base is about 9-1/2 inches deep on one side and 10-1/8 inches deep on the other. Installation...Read more requires no tools. Place the bin slightly above the mounting points, then slide it down until it locks into place. Compare the size, shape, and side mounts with the original bin before ordering.
This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as ...Read morethey commonly wear at the same rate. This is about 1 inch long and metallic in color.
This refrigerator door bin provides handy storage for condiments, jars, bottles, and other small items. It attaches to the inside of the door, keeping everyday foods easy to reach while freeing up space on the main shelves. The raised sides help keep items in place as the door opens and closes. Cracks, broken mounting tabs, or a damaged b...Read morease may leave the bin loose or unable to hold items safely. Replacing a broken bin restores useful storage and helps keep your refrigerator organized. This is an OEM part sourced directly from the manufacturer.
This air filter assembly is a genuine replacement part designed to improve air quality inside select LG and Kenmore Elite refrigerators. Using activated carbon, it effectively traps and neutralizes odors and airborne impurities, helping maintain a clean environment that supports longer food freshness. The filter is housed within a dedicat...Read moreed compartment and should be replaced approximately every six months or when indicated by the refrigerator’s filter light. Installation involves locating the filter housing, powering off the appliance, removing the old filter, and inserting the new one with proper alignment. After installation, reassemble the housing, restore power, and reset the filter indicator to ensure accurate tracking. This OEM component ensures a precise fit and optimal performance for compatible models.
This is a manufacturer-approved refrigerator door closure for your refrigerator. It is made of white plastic and measures approximately 3 inches by 2 inches. If your old closure is damaged, your refrigerator door may not open and shut properly, and therefore it should be replaced.
This is a micro switch for various models of LG refrigerators. This switch is responsible for turning the ice dispenser on and off within the freezer compartment of the fridge. If this switch is damaged or shorted, it will cause the ice maker to work inconsistently, or not at all. This switch is different from the water dispenser switch, ...Read morewhich has an entirely different shape all together. Replacing this switch is simple and only requires a Philips-head screwdriver to disconnect the old switch and install the new one. This switch is a genuine OEM LG part and does not come with any other parts or accessories.
NOTE: The Secondary (smaller) wire connector has 3 wires in it. If original ice maker has 6 wire connector see part number AEQ73110205. Please verify connector before ordering.
Dispensing water and filling the ice maker require controlled flow through this refrigerator water inlet valve assembly. Electrically operated solenoids open the water passages when requested by the appliance controls and close them when delivery ends. A cracked or faulty valve may leak, restrict dispenser flow, or prevent the ice maker f...Read morerom receiving enough water. Replacing a failed assembly helps restore reliable water routing and proper shutoff between requests. It connects the incoming supply to the internal water circuits used during everyday dispensing and ice production. This is an OEM part sourced directly from the manufacturer.
This water tubing clip holds the water fill tube in place in your refrigerator. The water fill tube attaches and supplies water to the ice maker/water dispenser in your fridge-freezer. If the tubing is in working order, but is hanging loose inside the unit, the issue could be that the clip meant to hold it in place is broken. If this is t...Read morehe case, you should look to replace the clip. This clip is made of black plastic, and is just over half an inch long. This is a genuine OEM replacement part, and is sold separately.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Remove and replace light switch
45 of 91 peoplefound this instruction helpful.
Debbie from Waltham, MA
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers
Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.
Was this helpful?
Thank you for voting!
Fridge light would not come on.
10 of 22 peoplefound this instruction helpful.
Grace from GALLOWAY, NJ
A Bit Difficult
15 - 30 mins
Screw drivers
After watching a few iTunes videos I was able to order the light switch from part select and within a week I had the new switch. I had a little trouble getting the switch out. I used a flat screw driver and taped around the edge to keep from damaging the wall inside. I found the clip on the right side and had to use some force to get it p
... Read moreopped out, you may need to use pliers to disconnect the switch.
Read less
Was this helpful?
Thank you for voting!
Light stopped working
6 of 10 peoplefound this instruction helpful.
Tamara from MONDOVI, WI
Really Easy
Less than 15 mins
Screw drivers
Have had the Sears repairman come to the house to replace this part in 5 minutes for +$100.. twice. When my dad's stopped working, ordered the part and replaced it myself for the cost of the part and shipping. Use a screw driver to pry the right side of the switch and pull out. Best to watch a youtube video first. Takes about 5 minut
... Read morees.