Opening the refrigerator door releases this push-button switch to turn on the interior light, making stored food easier to see. When the door closes, it presses the button and turns the light off. A stuck, worn, or broken switch may leave the light off when the door is open or keep it on after closing. Replacing a faulty switch helps rest...Read moreore normal lighting control and reliable response to door movement. Disconnect the refrigerator from power before removing or installing the switch. This is an OEM part sourced directly from the manufacturer.
This front plate assembly, also known as a mullion or flipper, is a genuine replacement part designed for select LG and Kenmore French-door refrigerators. It serves a critical function by sealing the gap between the doors, preventing cold air from escaping and helping maintain consistent internal temperatures. Constructed from durable pla...Read morestic, it supports both the performance and appearance of the appliance. A failing mullion may result in poor sealing, visible gaps, increased energy consumption, and potential food spoilage. Replacing this component can restore proper door alignment and improve overall efficiency. Compatibility should be confirmed using your refrigerator’s model number prior to installation.
This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as ...Read morethey commonly wear at the same rate. This is about 1 inch long and metallic in color.
Maintain a snug door seal with this grey right-side refrigerator door gasket. Its flexible edge presses against the cabinet when closed, helping keep cold air inside and warm, moist air out. Tears, cracks, or warped sections may leave gaps that cause condensation, frost buildup, or longer cooling cycles. Replacing a damaged gasket helps r...Read moreestore steady temperatures and reduce air leaks. Clean and dry the door channel before installing the new seal, then wipe the contact surface regularly to remove dirt and food residue. This is an OEM part sourced directly from the manufacturer.
Controlled door travel helps prevent a refrigerator door from swinging beyond its intended opening range. This white plastic door stopper mounts near the bottom of the door and provides a stopping point as it opens. A cracked, worn, or broken stopper may allow excessive movement or fail to stop the door normally. Replacing a damaged stopp...Read moreer helps restore the intended swing limit and reduces strain caused by overextension. The stopper works with the hinge assembly to provide a mechanical limit during everyday opening and closing. This is an OEM part sourced directly from the manufacturer.
This deli drawer is for refrigerators. Deli drawer holds meats, vegetables and snacks in the fresh food compartment of the refrigerator. Follow the instructions in the owner's manual when installing this part.
Everyday drinks and condiments stay organized in this refrigerator door shelf bin. Its white plastic frame supports jars and bottles, while the clear front makes contents easy to see. The bin attaches to slots inside the door, adding storage without taking up room on the main shelves. A cracked base, broken mounting tabs, or damaged front...Read more panel may leave containers poorly supported. Replacing a worn or broken bin restores useful storage and helps keep items secure as the door opens and closes. This is an OEM part sourced directly from the manufacturer.
Proper movement of the center door flap helps a French door refrigerator seal the gap between its doors. This mullion spring applies tension to the hinged flap, guiding it as the door opens and closes. A broken, stretched, or missing spring may leave the flap loose or prevent it from moving into place, making door closure difficult. Repla...Read morecing a damaged spring helps restore controlled flap movement and proper sealing. Its coiled design stores and releases force as the mullion pivots during everyday use. This is an OEM part sourced directly from the manufacturer.
This ice maker assembly is for refrigerators. This Ice maker assembly contains the complete ice maker and housing. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
This is a manufacturer-approved refrigerator door closure for your refrigerator. It is made of white plastic and measures approximately 3 inches by 2 inches. If your old closure is damaged, your refrigerator door may not open and shut properly, and therefore it should be replaced.
This is a door gasket for the right side of various models of LG refrigerators. Door gaskets, also known as seals, are used to create a barrier between the outside ambient temperature of your home and the cool-controlled internal temperature of the refrigerator. If your refrigerator door seal is warped, cracking, or damaged in any way, it...Read more is important to replace it as soon as possible to ensure optimal cooling performance from your fridge. This is a gray-colored OEM door seal that simply needs to be wrapped carefully around the perimeter of your refrigerator door.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Remove and replace light switch
45 of 91 peoplefound this instruction helpful.
Debbie from Waltham, MA
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers
Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.
Was this helpful?
Thank you for voting!
The factory door gasket was split and needed replacing
22 of 36 peoplefound this instruction helpful.
Carl from LAKE WYLIE, SC
Very Easy
Less than 15 mins
I pulled the gasket off and installed the new one. It was very easy. All I had to do was to push the new gasket in place in the grooves in the door. The gasket I received was identical to the one I replaced.
Was this helpful?
Thank you for voting!
My nephew accidentally forced the door closed last year, which resulted in the door having to be re closed manually folding back the flap. Ugh!
25 of 46 peoplefound this instruction helpful.
Tiziana from WARWICK, NY
Really Easy
Less than 15 mins
Nutdriver
Unscered 2 screws, unplug electrical connection under the screws, slide her flap into grooves, realign screw holes , and rescrew in. Done.