This refrigerator door shelf bin is designed to provide organized, accessible storage for bottles, condiments, and packaged items within the fresh-keeping section of the refrigerator door. Made from thickened, food-grade plastic, it offers durability and a secure fit. Measuring approximately 10.6" x 7.2" x 3.6", this bin is specifically d...Read moreesigned for the left-side upper three bins and the right-side middle two bins in select LG and Kenmore refrigerator models. Though the design may have been updated, it maintains full compatibility and functionality with the original part. Installation is straightforward and requires no tools, making it an ideal solution for replacing a cracked or missing bin and restoring optimal storage capacity.
This genuine refrigerator pantry drawer front cover provides a finished front panel for the pantry or deli drawer while helping keep stored foods organized and protected. Made from durable clear plastic with decorative trim, it serves as a replacement for a cracked, damaged, or worn drawer front and helps maintain smooth drawer operation ...Read moreand a clean appearance inside the refrigerator. The cover measures approximately 17 inches wide, 7 inches high, and 1 inch deep.
This refrigerator door hinge bushing is a durable white plastic component that provides a smooth pivot point for the hinge pin, helping keep the door properly aligned and sealed. It is commonly used to correct doors that sag, make noise, or are difficult to open or close due to a worn or damaged bushing. The bushing installs at the door h...Read moreinge pivot point and typically requires removing the hinge bracket with a 10?mm socket. Color is white, and size and dimensions may vary by refrigerator model.
This ice maker assembly is for refrigerators. This Ice maker assembly contains the complete ice maker and housing. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
This is a manufacturer-approved refrigerator door closure for your refrigerator. It is made of white plastic and measures approximately 3 inches by 2 inches. If your old closure is damaged, your refrigerator door may not open and shut properly, and therefore it should be replaced.
This is a micro switch for various models of LG refrigerators. This switch is responsible for turning the ice dispenser on and off within the freezer compartment of the fridge. If this switch is damaged or shorted, it will cause the ice maker to work inconsistently, or not at all. This switch is different from the water dispenser switch, ...Read morewhich has an entirely different shape all together. Replacing this switch is simple and only requires a Philips-head screwdriver to disconnect the old switch and install the new one. This switch is a genuine OEM LG part and does not come with any other parts or accessories.
This part must be installed by a licensed and trained LG technician that is able to perform a software update, which is required for the installation of this compressor. Part number CJT30000002 is needed to perform the update.
Also, the three pins on the side of the new compressor may be oriented differently than the original. If diff...Read moreerent, when installing the new compressor the compressor electrical connector must be rotated 45 degrees counter-clockwise.
This refrigerator water filter and filter assembly is designed to improve the quality of drinking water and ice by reducing contaminants such as chlorine, lead, and sediment. Certified to NSF standards 42 and 53, it enhances taste and clarity while allowing beneficial minerals to pass through. Compatible with select bottom-freezer refrige...Read morerator models, this genuine replacement part should be installed using a simple twist-in method and replaced every six months or when water flow slows. After installation, flushing approximately four gallons of water ensures optimal performance and removes any residual carbon particles. Regular replacement supports consistent filtration and helps maintain the appliance’s performance.
This fan assembly circulates air through the appliance to support proper temperature control and ventilation. Designed for quiet and efficient airflow, it is replaced when airflow weakens, noise increases, or cooling performance declines.
This part is a temperature sensing devise. It senses the rise in evaporator temperature during a defrost cycle and cycles the defrost heater off after all frost is melted. It is calibrated to permit a defrost cycle only when the temperature is below a preset temperature.
This roller assembly supports smooth movement of drawers or internal components, reducing friction and strain. Quiet, easy motion improves usability and helps prevent wear. Replacing a worn roller restores smooth, reliable operation.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
old bushing worn and broken
23 of 43 peoplefound this instruction helpful.
Jerry from CORSICANA, TX
Really Easy
30 - 60 mins
Screw drivers, Socket set
removed the upper freezer door to access screws to remove lower door. laid bottom door on its side, removed bad bushing, put new bushing in, put bottom door back on refridge, put upper door back on fridge. Door worked easy as when new. good closure of door and story..Happy customer, and wife even happier.....thank you....
Was this helpful?
Thank you for voting!
Icemaker quit releasing ice from tray and water was pouring and freezing in ice storage bin
13 of 24 peoplefound this instruction helpful.
Amber from PEORIA, IL
Really Easy
15 - 30 mins
Screw drivers
This couldn't have been easier. Two tiny screws in the front needed unscrewed, and then two plastic clips in the middle just had to be popped lose. Finally, you unplugged the power cord. Then, you just needed to reverse the process by plugging the new ice maker in, popping the clips in place, and screwing the two holes back in and turning
... Read more the whole thing on. Voila! Perfect ice cubes again. And for only a little over $100.
Read less
Was this helpful?
Thank you for voting!
needed to replace broken ice maker
11 of 18 peoplefound this instruction helpful.
John from WEST ROCKPORT, ME
Very Easy
Less than 15 mins
Screw drivers
Take out 2 screws and unplug unit before removing. Plug-in new unit and screw in 2 screws. That's it.